Background and Objectives. Charcoal-containing toothpastes have become popular among many patients; however, there is inadequate scientific evidence on oral health. This study aimed to evaluate the color change, surface microhardness, and roughness of bovine enamel and composite resin submitted to simulated toothbrushing with a whitening toothpaste containing activated charcoal. Methods. Thirty-six bovine incisors and resin composite samples were prepared, stained with black tea, and then randomly divided into two groups. The samples were brushed with a charcoal-containing toothpaste (Colgate® MAX WHITE) and daily toothpaste (Colgate® Max Fresh) for 10,000 cycles. Before and after brushing cycles, color variables (ΔL, Δa, Δb), total color change (ΔE), plus Vickers microhardness were evaluated. Two samples of each group were prepared for surface roughness assessment via atomic force microscope. Data were analyzed by Shapiro–Wilk, Independent sample t-test and Mann–Whitney U tests. Results. According to the obtained results, ΔE and ΔL were significantly higher whereas Δa and Δb were noticeably lower in charcoal-containing toothpaste group in comparison with daily toothpaste in both composite and enamel samples. The microhardness of samples brushed with Colgate® MAX WHITE was significantly higher than that of Colgate® Max Fresh in enamel ( P = 0.04 ), whereas no significant difference was found in composite resin samples ( P = 0.23 ). Colgate® MAX WHITE enhanced the roughness of both enamel and composite surfaces. Conclusion. The charcoal-containing toothpaste could improve the color of both enamel and resin composite with no negative effect on microhardness. Nevertheless, its adverse roughening effect should be considered occasionally on composite restorations.

The aim of this study was to evaluate the effect of bleaching and thermocycling on microshear bond strength of bonded resin composites to enamel. Enamel slices were prepared from ninety-six intact human premolars and resin composite cylinders were bonded by using Adper Single Bond 2 + Filtek Z350 or Filtek silorane adhesive and resin composite. Each essential group was randomly subdivided to two subgroups: control and bleaching. In bleaching group, 35% hydrogen peroxide was applied on samples. Thermocycling procedure was conducted between 5°C and 55°C, for 3.000 cycles on the half of each subgroup specimen. Then microshear bond strength was tested. Methacrylate-based resin composite had higher bond strength than silorane-based one. The meyhacrylate-based group without bleaching along with thermocycling showed the most bond strength, while bleaching with 35% carbamide peroxide on silorane-based group without thermocycling showed the least microshear bond strength. Bleaching caused a significant degradation on shear bond strength of silorane-based resin composites that bonded using self-etch adhesive resin systems.

PURPOSEThe purpose of the current study was to evaluate the effect of incorporating nanoparticles of silver (NAg) and amorphous calcium phosphate (NACP) into a self-etching primer of a resin cement on the microtensile bond strength of dentin, regarding the proven antibacterial feature of NAg and remineralizing effect of NACP.MATERIALS AND METHODSFlat, mid-coronal dentin from 20 intact extracted human third molars were prepared for cementation using Panavia F2.0 cement. The teeth were randomly divided into the four test groups (n=5) according to the experimental cement primer composition: cement primer without change (control group), primer with 1% (wt) of NACP, primer with 1% (wt) of physical mixture of NACP+Nag, and primer with 1% (wt) of chemical mixture of NACP+Nag. The resin cement was used according to the manufacturer's instructions. After storage in distilled water at 37℃ for 24 h, the bonded samples were sectioned longitudinally to produce 1.0 × 1.0 mm beams for micro-tensile bond strength testing in a universal testing machine. Failure modes at the dentin-resin interface were observed using a stereomicroscope. The data were analyzed by one-way ANOVA and Tukey's post-hoc tests and the level of significance was set at 0.05.RESULTSThe lowest mean microtensile bond strength was obtained for the NACP group. Tukey's test showed that the bond strength of the control group was significantly higher than those of the other experimental groups, except for group 4 (chemical mixture of NACP and NAg; P=.67).CONCLUSIONNovel chemical incorporation of NAg-NACP into the self-etching primer of resin cement does not compromise the dentin bond strength.

: The prevalence of periodontitis is around 20-50% of global population. If not treated, it can cause of tooth loss. Periodontal treatment aims at preserving the patient's teeth from various methods, including infection control and restoring lost periodontal tissue. The periodontium has great biological regenerative potential, and several biomaterials can be used to improve the outcome of periodontal treatment. To achieve the goal of periodontal tissue regeneration, numerous studies have used fibroblast growth factor 2 (FGF2) to stimulate regeneration of both soft tissue and bone. : FGF2 induced significant increment of the percentage of bone fill, bone mineral levels of the defect sites, length of the regenerated periodontal ligament, angiogenesis, connective tissue formation on the root surface, formation of dense fibers bound to alveolar bone and newly synthesized cementum in teeth. This review will open further avenues to better understand of FGF2 therapy for periodontal regeneration.

No abstract

Background and Aim: One of the weaknesses of Class II composite resin restorations is gingival microleakage which contributes to postoperative sensitivity and secondary caries. The aim was to evaluate the microleakage in Class II composite resin restorations with different thicknesses of resin-modified glass ionomer (RMGI). Materials and Methods: In this in-vitro study, standardized Class II slot cavities were prepared on the proximal surfaces of 90 molars. In group 1, total-etch adhesive and composite resin were applied using the incremental technique. In group 2, total-etch adhesive and composite were applied using the bulk technique. In group 3, 1 mm of RMGI was applied over the gingival floor, which was covered with increments of composite. In group 4, 1 mm of RMGI was placed on the gingival floor and covered with composite using the bulk technique. In group 5, 2 mm of RMGI was applied over the gingival floor, followed by an incremental composite placement. In group 6, 2 mm of RMGI was placed on the gingival floor, and the cavity was filled using the bulk technique. After thermocycling and staining with methylene blue, the samples were sectioned, and the extent of dye penetration was examined under a stereomicroscope. Data were analyzed using Kruskal-Wallis test and logistic regression (α=0.05). Results: The lowest and highest dye penetrations were observed in the first, second, and fifth groups, respectively. The RMGI thickness did not influence the microleakage scores significantly in either composite placement techniques (P=0.828). Conclusion: None of the restorative techniques completely eliminated microleakage of Class II composite resin restorations.

: Periodontal diseases are highly prevalent and can affect high percentage of the world population. Oxidative stress and inflammation plays an important role in the pathogenesis of periodontal diseases. Nowadays, more attention has been focused on the herbal remedies in the field of drug discovery. Green tea is an important source of polyphenol antioxidants, it has long been used as a beverage worldwide. The most interesting polyphenol components of green tea leaves that are related with health benefits are the catechins. Taken together this review suggested that green tea with its wide spectrum of activities could be a healthy alternative for controlling the damaging reactions seen in periodontal diseases.

No abstract