Nanocomposites combining a high breakdown strength polymer and high dielectric permittivity ceramic filler have shown great potential for pulsed power applications. However, while current nanocomposites improve the dielectric permittivity of the capacitor, the gains come at the expense of the breakdown strength, which limits the ultimate performance of the capacitor. Here, we develop a new synthesis method for the growth of barium strontium titanate nanowires and demonstrate their use in ultra high energy density nanocomposites. This new synthesis process provides a facile approach to the growth of high aspect ratio nanowires with high yield and control over the stoichiometry of the solid solution. The nanowires are grown in the cubic phase with a Ba0.2Sr0.8TiO3 composition and have not been demonstrated prior to this report. The poly(vinylidene fluoride) nanocomposites resulting from this approach have high breakdown strength and high dielectric permittivity which results from the use of high aspect ratio fillers rather than equiaxial particles. The nanocomposites are shown to have an ultra high energy density of 14.86 J/cc at 450 MV/m and provide microsecond discharge time quicker than commercial biaxial oriented polypropylene capacitors. The energy density of our nanocomposites exceeds those reported in the literature for ceramic/polymer composites and is 1138% greater than the reported commercial capacitor with energy density of 1.2 J/cc at 640 MV/m for the current state of the art biaxial oriented polypropylene.

Graphene consists of a monolayer of sp(2) bonded carbon atoms and has attracted considerable interest over recent years due to its extreme mechanical, electrical, and thermal properties. Graphene nanocomposites have naturally begun to be studied to capitalize upon these properties. A range of complex chemical and physical processing methods have been devised that achieve isolated graphene sheets that attempt to prevent aggregation. Here we demonstrate that the simple casting of a polymer solution containing dispersed graphene oxide, followed by thermal reduction, can produce well-isolated monolayer reduced-graphene oxide. The presence of single layer reduced-graphene oxide is quantitatively demonstrated through transmission electron microscopy and selected area electron diffraction studies and the reduction is verified by thermogravimetric, X-ray photoelectron spectroscopy, infrared spectrum, and electrical conductivity studies. These findings provide a simple, environmentally benign and commercially viable process to produce reduced-graphene oxide reinforced polymers without complex manufacturing, dispersion or reduction processes.

High energy density capacitors are critically important in advanced electronic devices and power systems since they can reduce the weight, size and cost required to meet a desired application. Nanocomposites hold strong potential for increasing the performance of high power energy sources; however, the energy density of most nanocomposites is still low compared to commercial capacitors and neat polymers. Here, we develop a new synthesis method for the growth of high aspect ratio barium titanate nanowires (BaTiO3) nanowires (NWs) with high yield. High energy density nanocomposite capacitors are fabricated using surface‐functionalized high aspect ratio BaTiO3 NWs in a poly(vinylidene fluoride‐trifluoroethylene‐chlorofluoroethylene) (P(VDF‐TrFE‐CFE)) matrix. At a 17.5% volume fraction, the nanocomposites show more than 45.3% increase in energy density above that of the pure P(VDF‐TrFE‐CFE) polymer (10.48 J/cc compared to 7.21 J/cc) at electric field 300 MV/m. This value is significant and exceeds those reported for the conventional polymer‐ceramic nanocomposites; it is also more than seven times larger than high performance commercial polypropylene capacitor (1.2 J/cc at 640 MV/m). In addition, our nanocomposite capacitor has a maximum power density as high as 1.2 MW/cc occurring only 1.52 μs after the start of discharge. The findings of this research could lead to enhanced interest in nanowires based nanocomposites due to their potential for achieving next generation energy storage devices.

The aspect ratio of barium titanate (BaTiO3) nanowires is demonstrated to be successfully controlled by adjusting the temperature of the hydrothermal growth from 150 to 240 °C, corresponding to aspect ratios from 9.3 to 45.8, respectively. Polyvinylidene fluoride (PVDF) nanocomposites are formed from the various aspect ratio nanowires and the relationship between the dielectric constant of the nanocomposite and the aspect ratio of the fillers is quantified. It was found that the dielectric constant of the nanocomposite increases with the aspect ratio of the nanowires. Nanocomposites with 30 vol % BaTiO3 nanowires and an aspect ratio of 45.8 can reach a dielectric constant of 44.3, which is 30.7% higher than samples with an aspect ratio of 9.3 and 352% larger than the polymer matrix. These results demonstrate that using high-aspect-ratio nanowires is an effective way to control and improve the dielectric performance of nanocomposites for future capacitor applications.

High energy storage plays an important role in the modern electric industry. Herein, we investigated the role of filler aspect ratio in nanocomposites for energy storage. Nanocomposites were synthesized using lead zirconate titanate (PZT) with two different aspect ratio (nanowires, nanorods) fillers at various volume fractions dispersed in a polyvinylidene fluoride (PVDF) matrix. The permittivity constants of composites containing nanowires (NWs) were higher than those with nanorods (NRs) at the same inclusion volume fraction. It was also indicated that the high frequency loss tangent of samples with PZT nanowires was smaller than for those with nanorods, demonstrating the high electrical energy storage efficiency of the PZT NW nanocomposite. The high aspect ratio PZT NWs showed a 77.8% increase in energy density over the lower aspect ratio PZT NRs, under an electric field of 15 kV mm(-1) and 50% volume fraction. The breakdown strength was found to decrease with the increasing volume fraction of PZT NWs, but to only change slightly from a volume fraction of around 20%-50%. The maximum calculated energy density of nanocomposites is as high as 1.158 J cm(-3) at 50% PZT NWs in PVDF. Since the breakdown strength is lower compared to a PVDF copolymer such as poly(vinylidene fluoride-tertrifluoroethylene-terchlorotrifluoroethylene) P(VDF-TreEE-CTFE) and poly(vinylidene fluoride-co-hexafluoropropylene) P(VDF-HFP), the energy density of the nanocomposite could be significantly increased through the use of PZT NWs and a polymer with greater breakdown strength. These results indicate that higher aspect ratio fillers show promising potential to improve the energy density of nanocomposites, leading to the development of advanced capacitors with high energy density.