The unique properties of nanoparticles and nanoparticle clusters show high potential for nanomaterials to be formulated into numerous products. In this paper, nanosuspensions are formulated by breaking up nanoparticle clusters (called agglomerates) in high-shear flows. A new breakage model is introduced to interpret erosive dispersion of agglomerates, and the population balance modeling is applied to account for effects of breakage on agglomerate size distribution. Effects of suspension structure on its rheology and flow are included in modeling. The population balance equations are solved using the quadrature method of moments (QMOM) that is linked directly to the k−ε model of the computational fluid dynamics (CFD) code FLUENT. In dispersion experiments, the aqueous suspensions of fumed silica particles, Aerosil 200V, are used. The test rig consists of an in-line Silverson rotor−stator mixer and a stirred tank. The head is a two-stage rotor−stator design with the inner stator consisting of round holes and the outer stator consisting of smaller square holes. Experimental results are compared with model predictions.

In-line rotor-stators are used in a wide range of industrial applications-primarily for dispersion processes such as emulsification, deagglomeration. Three rotor-stator heads have been used to investigate their performance in breaking up of nanoparticle clusters within a large project. This article reports the findings of a part of this study aimed at investigating the flow and power characteristics in single phase to highlight the differences of three different mixer heads. Power characteristics are determined using the calorimetry allowing the characteristic power numbers for these devices to be obtained. These are also compared with CFD calculations. Flow characteristics are studied through numerical simulations.

No abstract

Many chemical engineering processes involve the suspension of solid particles in a liquid. In dense systems, agitation leads to the formation of a clear liquid layer above a solid cloud. Cloud height, defined as the location of the clear liquid interface, is a critical measure of process performance. In this study, solid-liquid mixing experiments were conducted and cloud height was measured as a function operating conditions and stirred tank configuration. Computational fluid dynamics simulations were then performed using an Eulerian-Granular multiphase model. The effects of hindered and unhindered drag models and turbulent dispersion force on cloud height were investigated. A comparison of the experimental and computational data showed excellent agreement over the full range of conditions tested.

This study was carried out to investigate the break up of nanoparticle clusters in a liquid using an in-line rotor stator. Two types of fumed silica particles were dispersed in distilled water: Aerosil 200 V, which is hydrophilic, has a primary particle size of 12 nm and Aerosil R816 which is based on Aerosil 200 V and surface modified to render it hydrophobic. The article reports on the rheology of the dispersions, particle size analysis, the effect of concentration, and processing conditions such as the rotor speed, that is, the specific power input, and flow rate, that is, the residence time.

In-line rotor-stators are used for a wide range of power intensive dispersion applications, including the breakup of immiscible liquid droplets or agglomerates. This study, performed within the DOMINO project at BHR Group, aimed at studying the performance of three different rotor-stator head designs for deagglomeration processes. A given test system, nanoscale silica particles-in-water, was used to identify the mechanism and kinetics of break-up and determine the smallest attainable size. Three rotorstator head designs used were the GPDH-SQHS and EMSC screens from Silverson and Ytron Z-Lab from Ytron. These in-line rotor-stators were used in the recirculation loop of a stirred tank with a total dispersion volume of 100 litres. Power input and residence time were varied by changing the rotor speed and dispersion flow rate. Breakup was found to occur through erosion regardless of the operating conditions or rotor-stator design. The smallest fragments obtained were aggregates, rather than primary particles, and these were of a mean diameter of 150-200 nm; also independent of the operating conditions or rotor-stator head design. With a given rotor-stator operated at a given flow rate, increasing the rotor speed and hence the power input increased the break up kinetics. For a given design at a given specific power input, whilst the break up rate per tank turnover decreased when the flow rate was increased, the total processing time could be reduced. There were differences in the volume of the mixer head and chamber volumes; in addition, a smaller flow rate range could be covered with the Ytron design. Comparison of the different designs was therefore not straightforward. It could however be shown that the rotor-stator designs with a high number and small size of holes and/or gaps have a faster break up rate.

A commercial design, bench scale microfluidic processor, Microfluidics M110-P, was used to study the deagglomeration of clusters of nanosized silica particles. Breakup kinetics, mechanisms and the smallest attainable size were determined over a range of particle concentrations of up to 17% wt. in water and liquid viscosities of up to 0.09 Pa s at 1% wt. particle concentration. The device was found to be effective in achieving complete breakup of agglomerates into submicron size aggregates of around 150 nm over the range covered. A single pass was sufficient to achieve this at a low particle concentration and liquid viscosity. As the particle concentration or continuous phase viscosity was increased, either a higher number of passes or a higher power input (for the same number of passes) was required to obtain a dispersion with a size distribution in the submicron range. Breakup took place through erosion resulting in a dispersion of a given mean diameter range regardless of the operating condition. This is in line with results obtained using rotor-stators. Breakup kinetics compared on the basis of energy density indicated that whilst Microfluidizer M110-P and an in-line rotor-stator equipped with the emulsor screen are of similar performance at a viscosity of 0.01 Pa s, fines volume fraction achieved with the Microfluidizer was much higher at a viscosity of 0.09 Pa s.

No abstract