Moving mechanical interfaces are commonly lubricated and separated by a combination of fluid films and solid 'tribofilms', which together ensure easy slippage and long wear life. The efficacy of the fluid film is governed by the viscosity of the base oil in the lubricant; the efficacy of the solid tribofilm, which is produced as a result of sliding contact between moving parts, relies upon the effectiveness of the lubricant's anti-wear additive (typically zinc dialkyldithiophosphate). Minimizing friction and wear continues to be a challenge, and recent efforts have focused on enhancing the anti-friction and anti-wear properties of lubricants by incorporating inorganic nanoparticles and ionic liquids. Here, we describe the in operando formation of carbon-based tribofilms via dissociative extraction from base-oil molecules on catalytically active, sliding nanometre-scale crystalline surfaces, enabling base oils to provide not only the fluid but also the solid tribofilm. We study nanocrystalline catalytic coatings composed of nitrides of either molybdenum or vanadium, containing either copper or nickel catalysts, respectively. Structurally, the resulting tribofilms are similar to diamond-like carbon. Ball-on-disk tests at contact pressures of 1.3 gigapascals reveal that these tribofilms nearly eliminate wear, and provide lower friction than tribofilms formed with zinc dialkyldithiophosphate. Reactive and ab initio molecular-dynamics simulations show that the catalytic action of the coatings facilitates dehydrogenation of linear olefins in the lubricating oil and random scission of their carbon-carbon backbones; the products recombine to nucleate and grow a compact, amorphous lubricating tribofilm.

Lithium metal anodes can largely enhance the energy density of rechargeable batteries because of the high theoretical capacity and the high negative potential. However, the problem of lithium dendrite formation and low Coulombic efficiency (CE) during electrochemical cycling must be solved before lithium anodes can be widely deployed. Herein, a new atomic layer deposition (ALD) chemistry to realize the low-temperature synthesis of homogeneous and stoichiometric lithium fluoride (LiF) is reported, which then for the first time, as far as we know, is deposited directly onto lithium metal. The LiF preparation is performed at 150 °C yielding 0.8 Å/cycle. The LiF films are found to be crystalline, highly conformal, and stoichiometric with purity levels >99%. Nanoindentation measurements demonstrate the LiF achieving a shear modulus of 58 GPa, 7 times higher than the sufficient value to resist lithium dendrites. When used as the protective coating on lithium, it enables a stable Coulombic efficiency as high as 99.5% for over 170 cycles, about 4 times longer than that of bare lithium anodes. The remarkable battery performance is attributed to the nanosized LiF that serves two critical functions simultaneously: (1) the high dielectric value creates a uniform current distribution for excellent lithium stripping/plating and ultrahigh mechanical strength to suppress lithium dendrites; (2) the great stability and electrolyte isolation by the pure LiF on lithium prevents parasitic reactions for a much improved CE. This new ALD chemistry for conformal LiF not only offers a promising avenue to implement lithium metal anodes for high-capacity batteries but also paves the way for future studies to investigate failure and evolution mechanisms of solid electrolyte interphase (SEI) using our LiF on anodes such as graphite, silicon, and lithium.

No abstract

No abstract

The effects of oxidation on wear of carbon/steel tribological interfaces were studied. When mechanical wear was small, the oxidation behavior of hydrogenated diamond-like carbon (H-DLC) and stainless steel (SS) sliding interface varied depending on the nature of the oxidizing environment. In dry air or oxygen, both H-DLC and SS wore readily. The wear debris of SS did not form iron oxide in dry air and oxygen. In humid nitrogen, however, the wear of H-DLC diminished with increasing humidity, and the SS surface showed mild wear and iron oxide debris accumulated around the sliding contact region. These results revealed that different tribochemical reactions occur in dry oxygen and humid environments. In the absence of water, oxygen oxidizes the H-DLC surface, making it susceptible to wear, creating debris, and inducing wear on both H-DLC and SS. In contrast, adsorbed water molecules at less than 40% RH act as a molecular lubricant of the oxidized DLC surface, while multiwater layers adsorbed at near-saturation act as electrolyte inducing electrochemical galvanic corrosion reactions on the SS surface. When hydrogen-free amorphous carbon (a-C) was used in tribo-tests, severe wear of the SS surface occurs, in addition to the tribochemical wear observed for H-DLC, due to the high hardness of the a-C film.

Tribochemistry involves chemical reactions occurring at sliding contact interfaces in the presence of gaseous and/or liquid media. It often leads to the formation of a solid reaction film (also termed boundary film) which controls friction and wear and hence the efficiency and reliability of moving mechanical systems (such as engines). Here we demonstrate tribochemical conversion of methane to graphene, nano-onion, and disordered carbons on the sliding surfaces of Ni-, Cu-, and CuNi-containing VN coatings at atmospheric pressure and room temperature, providing 2–3 orders of magnitude reduction in wear and ∼50% reduction in friction compared to those of the uncoated steels. Transmission electron microscopy confirms that graphene forms preferably on metal rich nanoclusters of the composite coatings, while the carbon nano-onions are scattered throughout the carbon tribofilm. Ab initio molecular dynamics simulations elucidate underlying mechanisms involved in the tribochemical conversion of methane to carbon-based nanostructures in support of microscopic observations. These scientific findings may lead to new materials technologies that can use methane as a source for continuous and in situ lubrication. For example, there is an urgent need to curtail the uses of lubricating oils in natural gas compressors and engines as they contaminate the natural gas being compressed or burnt.

The characterization of any compound is important in the field of chemistry. As the field of cannabinoid chemistry grows so does the need for the characterization of new cannabinoids or rare cannabinoids that gain popularity within the consumer and research fields. Hexahydrocannabinol (HHC) a hydrogenated analogue of Δ9-tetrahydrocannabinol (THC), also found in trace amounts naturally within the Cannabis sativa plant, has been gaining attention and popularity within the cannabis industry. Hexahydrocannabidiol (H4CBD) is a synthetic hydrogenated analogue to cannabidiol (CBD). Identifying the diastereomers of the cannabinoids with instrumentation plays a huge role within the chemistry field adding valuable information of the structure and the parameters for others to identify such cannabinoids. Elucidation and characterization of HHC and H4CBD were performed using current analytical techniques such as 1D and 2D nuclear magnetic resonance (NMR), high performance liquid chromatography (HPLC), and gas chromatography-mass spectrometry (GC-MS), effectively characterizing both the diastereomers of HHC and H4CBD.

No abstract