Chalcopyrite solar cells achieve efficiencies above 23%. The latest improvements are due to post‐deposition treatments (PDT) with heavy alkalis. This study provides a comprehensive description of the effect of PDT on the chemical and electronic structure of surface and bulk of Cu(In,Ga)Se2. Chemical changes at the surface appear similar, independent of absorber or alkali. However, the effect on the surface electronic structure differs with absorber or type of treatment, although the improvement of the solar cell efficiency is the same. Thus, changes at the surface cannot be the only effect of the PDT treatment. The main effect of PDT with heavy alkalis concerns bulk recombination. The reduction in bulk recombination goes along with a reduced density of electronic tail states. Improvements in open‐circuit voltage appear together with reduced band bending at grain boundaries. Heavy alkalis accumulate at grain boundaries and are not detected in the grains. This behavior is understood by the energetics of the formation of single‐phase Cu‐alkali compounds. Thus, the efficiency improvement with heavy alkali PDT can be attributed to reduced band bending at grain boundaries, which reduces tail states and nonradiative recombination and is caused by accumulation of heavy alkalis at grain boundaries.
Concepts of localized contacts and junctions through surface passivation layers are already advantageously applied in Si wafer-based photovoltaic technologies. For Cu(In,Ga)Se2 thin film solar cells, such concepts are generally not applied, especially at the heterojunction, because of the lack of a simple method yielding features with the required size and distribution. Here, we show a novel, innovative surface nanopatterning approach to form homogeneously distributed nanostructures (<30 nm) on the faceted, rough surface of polycrystalline chalcogenide thin films. The method, based on selective dissolution of self-assembled and well-defined alkali condensates in water, opens up new research opportunities toward development of thin film solar cells with enhanced efficiency.
The properties and performance of polycrystalline materials depend critically on the properties of their grain boundaries. Polycrystalline photovoltaic materials – e.g. hybrid halide perovskites, copper indium gallium diselenide (CIGSe) and cadmium telluride – have already demonstrated high efficiencies and promise cost-effective electricity supply. For CIGSe-based solar cells, an efficiency above 23% has recently been achieved using an alkali-fluoride post-deposition treatment; however, its full impact and functional principle are not yet fully understood. Here, we show direct evidence for the passivation of grain boundaries in CIGSe treated with three different alkali-fluorides through a detailed study of the nanoscale optoelectronic properties. We determine a correlation of the surface potential change at grain boundaries with the open-circuit voltage, which is supported by numerical simulations. Our results suggest that heavier alkali elements might lead to better passivation by reducing the density of charged defects and increasing the formation of secondary phases at grain boundaries.
We study the impact of different alkali post‐deposition treatments by thermal admittance spectroscopy and temperature‐dependent current‐voltage (IVT) characteristics of high‐efficiency Cu(In,Ga)Se2 thin‐film solar cells fabricated from low‐temperature and high‐temperature co‐evaporated absorbers. Capacitance steps observed by admittance spectroscopy for all samples agree with the widely observed N1 signature and show a clear correlation to a transport barrier evident from IVT characteristics measured in the dark, indicating that defects are likely not responsible for these capacitance steps. Activation energies extracted from capacitance spectra and IVT characteristics vary considerably between different samples but show no concise correlation to the alkali species used in the post‐deposition treatments. Numerical device simulations show that the transport barrier in our devices might be related to conduction band offsets in the absorber/buffer/window stack.
This paper shows the application of simple dc techniques to the temperature-dependent characterization of AlGaN/ GaN HEMTs in terms of the following: 1) thermal resistance and 2) ohmic series resistance (at low drain bias). Despite their simplicity, these measurement techniques are shown to give valuable information about the device behavior over a wide range of ambient/channel temperatures. The experimental results are validated by comparison with independent measurements and numerical simulations.Index Terms-Gallium compounds, microwave power transistors, MODFETs, power HEMTs, semiconductor-device measurements, semiconductor-device thermal factors, wide bandgap semiconductors, III nitrides, III-V semiconductors.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.