This work presents the results on the high-energy ball milling and hot pressing of Ni-48Ti-2Sn and Ni-45Ti-5Sn (at-%) powder mixtures. The milling process was performed in a planetary ball mill using stainless steel vial (225 mL) and hardened steel balls (19 mm diameter), rotary speed of 300 rpm, and a ball-to-powder weight ratio of 10:1. Samples were collected into the vial after different milling times: 60, 180 and 300 min. In the sequence, wet milling (isopropyl alcohol) was adopted up to 720 min in order to increase the powder yield into the vials. The as-milled and hot-pressed samples were characterized by X-ray diffraction, electron scanning microscopy, and energy dispersive spectrometry. Results indicated that the ductile particles were promptly cold-welded during the initial milling times. XRD patterns of the Ni-48Ti-2Sn powder mixture indicated that the peaks of Ni, Ti and Sn disappeared after milling for 3h. Following, peaks of NiTi and Ni4Ti3were preferentially formed during milling of Ni-Ti-Sn powders. A large amount of fine powders was yielded into the vial after wet milling for 720 min only. No significant carbon or oxygen contamination was detected by EDS analysis. Hot pressing produced homogeneous and dense samples which presented microstructures containing a large amount of the NiTi compound.
This work discusses on the preparation of Ni-45Ti-5Mo, Ni-40Ti-10Mo and Ni-46Ti-2Mo-2Zr (at-%) alloys by high-energy ball milling and hot pressing, which are potentially attractive for dental and medical applications. The milling process was performed in stainless steel balls (19mm diameter) and vials (225 mL) using a rotary speed of 300rpm and a ball-to-powder weight ratio of 10:1. Hot pressing under vacuum was performed in a BN-coated graphite crucible at 900°C for 1 h using a load of 20 MPa. The milled and hot-pressed materials were characterized by X-ray diffraction, electron scanning microscopy, and electron dispersive spectrometry. Peaks of B2-NiTi and Ni4Ti3were identified in XRD patterns of Ni-45Ti-5Mo, Ni-40Ti-10Mo and Ni-46Ti-2Mo-2Zr powders milled for 1h. The NiTi compound dissolved small Mo amounts lower than 4 at%, which were measured by EDS analysis. Moreover, it was identified the existence of an unknown Mo-rich phase in microstructures of the hot-pressed Ni-Ti-Mo alloys.
The work reports on the phase transformation in mechanically alloyed and hot-pressed Nb-4Si-8B and Nb-8Si-16B (at-%) alloys. Elemental powder mixtures were processed in a planetary ball mill under argon atmosphere using 300 rpm, stainless steel balls (19 mm diameter) and vials (225 mL), and a ball-to-powder weight ratio of 10:1. After dry milling for 7h, wet milling with isopropyl alcohol for more 20 min was adopted to increase the recovering of previously cold-welded Nb-4Si-8B powders. To obtain the equilibrium structures the as-milled powders were hot-pressed under vacuum at 1200oC for 1 h. The as-milled powders and hot-pressed samples were characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectrometry. XRD results revealed the presence of metastable phases in as-milled Nb-Si-B powders. The hot pressing has produced dense Nb-Si-B samples, which were formed by the Nbss, Nb3B2and Fe2Nb phases beside of other unknown Si-rich phase.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.