In this work, polyester/TiO2 coatings on wood surfaces were prepared in one step via two deposition methods by using an atmospheric pressure plasma jet technique with the aim to further enhance the stabilization of the wood surfaces against UV-radiation and moisture. The first method, based on the combination of plasma spray powder (PSP) coating and liquid precursor plasma spraying (LPPS) coating techniques, used polyester powder and titanium tetraisopropoxide (TTIP) liquid precursor as feedstock. In the second method, the polyester/TiO2 coatings were prepared by using a mixed powder of polyester micro-particles and TiO2 nano-particles as feedstock and applied via plasma spray powder coating technique. The surface topology and morphology of the wood samples were observed by scanning electron microscopy (SEM). The SEM results showed the presence of a rough structure after coating with polyester/TiO2. The surface chemical compositions of the samples were characterized by X-ray photoelectron spectroscopy and by Fourier transform infrared spectroscopy. The wetting behaviour of the coated wood surfaces was studied by measuring the water contact angle. After coating a hydrophilic wood surface with polyester/TiO2 prepared via (PSP + LPPS), it showed excellent water repellency; the wood surfaces were transformed from hydrophilic to superhydrophobic, while the polyester/TiO2 coating prepared via (PSP) was hydrophilic. Protection against UV radiation-induced colour changes was determined by UV tests and photo-assisted analysis using the CIELab colour system. The abrasion test results indicated that the polyester-containing films had good abrasion resistance and good adhesion to the wood substrates.
In the present work, titanium dioxide (TiO2) coatings were deposited on wood surfaces by an atmospheric pressure plasma jet using titanium tetraisopropoxide (TTIP) as a precursor to improve the wood’s stability against ultraviolet (UV) light and its moisture resistance capability. The surface topology and morphology of the wood specimens were observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Surface chemical compositions of the specimens were characterized by X-ray photoelectron spectroscopy (XPS) and by Fourier transform infrared (FTIR) spectroscopy. The wettability of the coated wood was investigated by measuring the sessile contact angle. SEM and AFM showed the presence of small globules of TiO2 with some areas agglomerated on the coated wood surface. The coated surface roughness increased with increasing deposition time. FTIR analysis showed the existence of a Ti–O–Ti band at 800–400 cm−1 on the coated wood surfaces. The results obtained from FTIR were confirmed by XPS measurements. The hydrophilic wood surfaces were transformed to become hydrophobic or superhydrophobic after coating with TiO2, depending on the deposition parameters. The changes of colour during UV-exposure for both uncoated and coated wood specimens were measured using the CIELab colour system. The TiO2 coated wood became more resistant to colour change after UV radiation exposure than did untreated wood.
In the present work, the solution precursor plasma spray (SPPS) process was used to deposit zinc oxide (ZnO) coatings on wood surfaces using zinc nitrate solution as precursor to improve the hydrophobicity and the color stability of European beech wood under exposure to ultraviolet (UV) light. The surface morphology and topography of the wood samples and the coatings were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The formation of ZnO was detected with the help of X-ray photoelectron spectroscopy (XPS) and by Fourier transform infrared (FTIR) spectroscopy. The FTIR spectra of the coated samples showed the typical Zn–O band at 445 cm−1. According to the XPS analysis, the coatings consist of two different Zn-containing species: ZnO and Zn(OH)2. Variation of the deposition parameters showed that the most significant parameters affecting the microstructure of the coating were the solution concentration, the deposition scan speed, and carrier gas flow rate. The wettability behaviors of the coated wood were evaluated by measuring the water contact angle (WCA). The coatings that completely covered the wood substrates showed hydrophobic behaviors. UV-protection of wood surfaces after an artificial UV light irradiation was evaluated by color measurements and FTIR spectroscopy. The ZnO-coated wood surfaces were more resistant to color change during UV radiation exposure. The total color change decreased up to 60%. Additionally, the FTIR spectra showed that the wood surfaces coated with ZnO had more stability. The carbonyl groups formation and C=C-bonds consumption were significantly lower.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.