No abstract

The adsorption of crystal violet (CV) onto date palm fibers (DPFs) was examined in aqueous solution at 25°C. The experimental maximum adsorption capacity value was0.66×10−6. Langmuir, Freundlich, Elovich and Temkin models were applied to describe the equilibrium isotherms. The influence of pH and temperature on dye removal was evaluated. The percentage removal of CV dye by adsorption onto DPF at different pH and temperatures showed that these factors play a role in the adsorption process. Thermodynamic analysis was performed, and the Gibbs free energyΔGο, enthalpy changeΔHο, and entropyΔSοwere calculated. The negative values ofΔGοindicate spontaneous adsorption. The negative value ofΔHοindicates that the interaction between CV and DPF is exothermic, and the positive value ofΔSοindicates good affinity between DPF and CV. The kinetic data were fitted to a pseudo-second-order model.

CoO/Co3O4 nanoparticles (NPs) were synthesized by using a fresh egg white-assisted combustion method which acts as a new approach for green synthesis of this composite. This method was carried out by the direct heat of cobalt precursor with egg white at low temperature for very short period. In fact, this route is a novel, cheap and appropriate technique yielding nanoparticle-based materials. CoO/Co3O4 nanoparticles were characterized by examining the structure and identifying the elements and determining the morphology via XRD, FTIR, SEM, EDS and TEM techniques. The sample magnetic observations were measured through the use of a vibrating sample magnetometer (VSM). The results of XRD, EDS, SEM and TEM confirmed the positive synthesis of the cubic CoO/Co3O4 NPs with sponge crystals which proceed. For the as synthesized composite, 57.75 m2/g, 0.0148 cc/g and 10.31 nm were identified to be the SBET, Vp and ȓ, respectively. The cobalt oxide particles in their nature were polycrystalline, and the crystallite sizes varied from 10 to 20 nm. The magnetic measurement showed that the prepared nanocomposite displays room temperature ferromagnetism with an optimum value, 3.45 emu/g, of saturation magnetization.

ABSTRACT:The corrosion inhibition of steel in phosphoric acid by thiosemicarbazide derivatives has been studied using different chemical and electrochemical techniques. The observed order of increasing inhibition efficiency was correlated with changes in the molecular structures of the inhibitors. Potentiodynamic polarization curves indicate that the compounds are mixed-type inhibitors. Electrochemical impedance spectroscopy has been used successfully to evaluate the performance of the inhibitors. AC measurements showed that the dissolution process was activation-controlled. The kinetic-thermodynamic model and the Flory-Huggins adsorption isotherm described the experimental findings well. The number of active sites, binding constant and change in free energy were computed for all the inhibitors studied. It was found that the inhibitor molecule was adsorbed through more than one active centre and occupied more than one active site on the steel surface.

Corrosion inhibition of steel in phosphoric acid (H 3 PO 4 ) by thiosemicarbazide derivatives was studied using different chemical and electrochemical techniques. Protection efficiency up to 99% was obtained with small amounts (10 -4 M) of cinnamaldehyde thiosemicarbazone (CTSCN). The order of increasing inhibition efficiency was correlated with the modification of the molecular structure of the inhibitors. Empirical kinetic relationship was obtained describing the experimental data obtained from the different compounds used in this investigation. Potentiodynamic polarization curves indicated that the compounds acted primarily as mixed-type inhibitors. Electrochemical impedance spectroscopy showed that the charge-transfer resistance increased and the capacitance of the double layer decreased with increasing the concentration of the inhibitor in the medium, confirming adsorption process mechanism. At high concentrations (> 10 4 M), the capacitance of the double layer leveled off since maximum double-layer thickness was attained. Kinetic-thermodynamic model and Flory-Huggins adsorption isotherm described the experimental findings. Number of active sites, binding constant, and change of free energy were computed for all inhibitors studied. Based on the inhibitor, it was found that each organic molecule replaced one or more adsorbed water molecule from the steel surface. The influence of exposure time on the performance of crotonaldehyde thiosemicarbazone (CrTSCN) was studied. Results showed that the inhibitor performed better with time and at a critical concentration of 5 x 10 -4 M.Maximum protection efficiency was attained because of a strong adsorption on steel surface over the total period of immersion exceeding 30 h.

In this study, extracts of both treated and untreated date palm tree waste were used as inhibitors of carbon steel corrosion in 1 M HCl. The date palm wastes used were the fiber and leaflets of the plant, and the treatment process involved gum arabic solution. The electrochemical measurements showed that the extracts were efficient inhibitors. The treated wastes were more efficient inhibitors than untreated waste, and the leaflets were better inhibitors than the fibers. The effect of temperature on inhibition efficiency, thermodynamic parameters, and adsorption isotherms for the treated inhibitors were studied. It was found that the adsorption was endothermic, occurred spontaneously, and that the adsorption data fit Langmuir isotherm model.

A series of copper-based systems containing two different nanocomposites (Cu2O/CuO and Cu2O/Cu) was synthesized by the egg white assisted auto-combustion route. This method was distinguished by the simplicity of its steps, low cost, one-pot synthesis process at low temperature and, short time. The characterization of the as prepared nanocomposites was carried out by using X-ray diffraction (XRD), Fourier-transform infrared (FTIR), Scanning electron microscope (SEM) and transmission electron micrograph (TEM), Energy dispersive spectrometry (EDS) techniques. Surface and magnetic properties of the obtained systems were determined by using N2 adsorption/desorption isotherms at 77 K and the vibrating sample magnetometer (VSM) technique. XRD results confirmed the formation of Cu2O/CuO and Cu2O/Cu nanocomposites with different ratios of well crystalline CuO, Cu2O, and Cu phases. FTIR results of the combusted product displays the presence of both CuO and Cu2O, respectively. SEM/EDS and TEM results confirm the formation of a porous nanocomposite containing Cu, O, and C elements. The change in concentration of the oxygen vacancies at the surface or interface of both Cu2O/CuO and Cu2O/Cu nanoparticles resulted in different changes in their magnetization. Based on this study, it is possible to obtain nanocomposite-based copper with multiple valances by a simple and inexpensive route which can be suitable for the fabrication of different transition metal composites.

Wild herbs (Origanum (OR) and Lavandula (LV)) were used as environment-friendly adsorbents in this study. The adsorbents were used for adsorption of Cu and Ba from water. The adsorption of heavy metals onto OR and LV was dependent on particle size, dose, and solution pH. The diameter of adsorbent particles was less than 282.8 nm. The adsorption follows second-order kinetics. Langmuir and Freundlich models have been applied to describe the equilibrium data, and the thermodynamic parameters, the Gibbs free energy, ∆G°, enthalpy, ∆H°, and entropy, ∆S°, have been determined. The positive value of ∆H° suggests that the adsorption of heavy metals by the wild herbs is endothermic. The negative values of ∆G° at all the studied temperatures indicate that the adsorption is a spontaneous process. It can be concluded that OR and LV are promising adsorbents for the removal of heavy metals from aqueous solutions over a range of concentrations.