Electrically conductive, polymeric materials that maintain their conductivity even when under significant mechanical deformation are needed for actuator electrodes, conformable electromagnetic shielding, stretchable tactile sensors, and flexible energy storage. The challenge for these materials is that the percolated, electrically conductive networks tend to separate even at low strains, leading to significant piezoresistance. Herein, deformable conductors are fabricated by spray‐coating a nitrile substrate with a graphene–elastomer solution. The electrical resistance of the coatings shows a decrease after thousands of bending cycles and a slight increase after repeated folding‐unfolding events. The deformable conductors double their electrical resistance at 12% strain and are washable without changing their electrical properties. The conductivity–strain behavior is modeled by considering the nanofiller separation upon deformation. To boost the conductivity at higher strains, the production process is adapted by stretching the nitrile substrate before spraying, after which it is released. This adaption meant that the electrical resistance doubles at 25% strain. The electrical resistance is found sufficiently low to give a 1.9 dB µm−1 shielding in the 8–12 GHz electromagnetic band. The physical and electrical properties, including the electro magnetic screening, of the flexible conductors, are found to deteriorate upon cycling but can be recovered through reheating the coating.

Materials for electronics that function as electrical and/or thermal conductors are often rigid, expensive, difficult to source, and sometimes toxic. An electrically and thermally conductive nanocomposite that is lightweight, flexible, and ecofriendly could improve the environmental friendliness of the electronics sector and enable new applications. Considering this, flexible and electrically and thermally conductive materials are fabricated by functionalizing paper with nanocarbon conductive inks. Carnauba wax is emulsified in isopropyl alcohol and mixed with graphene nanoplatelets (GNPs) or with hybrids of GNPs and carbon nanofibers (CNFs). The percolation threshold of the hybrid samples is lowered compared with the pure GNP composites, due to their increased filler aspect ratio. The hybrid samples also exhibit superior bending and folding stability. Densification of the coating to decrease their sheet resistance enables them to achieve as low as ≈50 Ω sq−1 for the GNP‐based paper. The densification procedure improves the bending stability, the abrasion resistance, and the electromagnetic interference shielding of the paper‐based conductors. Finally, the compressed samples show an impressive enhancement of their thermal diffusivity. The flexible and multifunctional nanocarbon coated paper is a promising electrical conductor and thermally dissipative material and, at the same time, can increase the environmental sustainability of the electronics sector.

A green textile-based conductor with controllable electrical resistance change with deformation and transiency (i.e., dissolution in water) will be the holy grail in wearable electronics since it can satisfy divergent needs with a single solution and be sustainable simultaneously. Nevertheless, designing such material is challenging since opposite requirements shall be satisfied. To solve such a problem, cotton is functionalized using conductive inks made of graphene or carbon nanofiber, a biodegradable polyvinyl alcohol binder, and environmentally friendly solvents. The electrical resistance shows an anisotropic response to bending depending on the composition of the coating and the stress direction, functioning either as a deformable compliant electrode or a tunable piezoresistor. Indeed, it can withstand thousands of bending cycles with a change in resistance of less than 5% or change its resistance by many orders of magnitude with the same deformation thanks to the combination of cotton twill and different nanofillers. A simple modification in the binder composition adding waterborne polyurethane allows the coating to go from entirely transient in water within minutes to withstanding simulated washing cycles for hours without losing its electrical conductivity. This green versatile conductor may serve opposing needs by altering the material composition and the deformation direction.

The use of two-dimensional materials in bulk functional applications requires the ability to fabricate defect-free 2D sheets with large aspect ratios. Despite huge research efforts, current bulk exfoliation methods require a compromise between the quality of the final flakes and their lateral size, restricting the effectiveness of the product. In this work, we describe an intercalation-assisted exfoliation route, which allows the production of high-quality graphene, hexagonal boron nitride, and molybdenum disulfide 2D sheets with average aspect ratios 30 times larger than that obtained via conventional liquid-phase exfoliation. The combination of chlorosulfuric acid intercalation with in situ pyrene sulfonate functionalisation produces a suspension of thin large-area flakes, which are stable in various polar solvents. The described method is simple and requires no special laboratory conditions. We demonstrate that these suspensions can be used for fabrication of laminates and coatings with electrical properties suitable for a number of real-life applications.

Investigation of novel and high-performance transparent conducting electrodes (TCEs) is required to substitute currently widely used tin-doped indium oxide (ITO) due to the low abundance of indium and constantly increasing...