For the purpose of this research, single track details were manufactured in the shape of thin walls with a length of 100 mm and a height of 80 mm. Two welding speeds were chosen for this experiment–13.3 mm/s and 20.0 mm/s corresponding to the following heat inputs: 120 J/mm and 80 J/mm. The gas metal arc welding (GMAW) method was used for the build-up of the specimens in the cold arc pulse mode. The structure of the specimens was studied using X-ray diffraction (XRD) analysis carried out with CuKα radiation with a wavelength of 1.5406 Ǻ, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). Furthermore, the Vickers hardness of the samples was determined using a ZwickRoell DuraScan 10/20 G5 unit at a force of 1 N. A preferred crystallographic orientation towards the (200) plane was observed in all cases, however a vastly textured structure was observed with inclusions of peaks in the (111), (220), and (311) crystallographic planes. The full width at half maximum (FWHM) of samples taken from different stages of build-up was calculated indicating an increase of the dislocation density at the more advanced stages of specimen growth. Despite that an increase of the hardness was observed towards the top of both specimens. This is attributed to the change in the structure of the αAl + Si formations from an irregular one at the bottom of the specimens, towards a fibrous one at the top. The results are discussed in regard to the optimization of the build-up process during wire arc additive manufacturing (WAAM).
This work presents the results of the electron-beam welding of commercially pure α-Ti (CP-Ti) and Ti6Al4V (Ti64) alloys. The structure and mechanical properties of the formed welded joints were examined as a function of the power of the electron beam. The beam power was set to P1 = 2100 W, P2 = 1500 W, and P3 = 900 W, respectively. X-ray diffraction (XRD) experiments were performed in order to investigate the phase composition of the fabricated welded joints. The microstructure was examined by both optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The mechanical properties of the formed joints were studied using tensile test experiments and microhardness experiments. The results of the experiments were discussed concerning the influence of the beam power on the microstructure and the mechanical properties of the weld joints. Furthermore, the practical applicability of the present method for the welding of α-Ti and Ti64 was also discussed.
In this study, we present the results of electron-beam welding of joints with 304-L stainless steel and copper. The influence of the beam’s power on the structures and mechanical properties of the welded joints was studied; the experiments were realized at a beam deflection of 0.3 mm to the Cu plate and beam powers of 2400, 3000, and 3600 W. The phase compositions of the obtained welded joints were studied by using X-ray diffraction (XRD); the microstructure and chemical composition were investigated by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX), respectively. The mechanical properties were studied by using tensile experiments and microhardness investigations. The phase compositions of the welded joints were in the forms of substitutional solid solutions between Fe, Cu, and pure copper and remained unchanged in terms of power. It was found that the microstructures changed gradually with the application of different values of the power of the electron beam. The results of the tensile tests showed higher tensile strengths at lower beam powers (i.e., 2400 and 3000 W) that dropped at 3600 W. The relative elongations rose with increases in the power of the electron beam. Moreover, it was found that the microhardnesses strongly depended on the applied technological conditions (defined by the electron beam’s power) and the corresponding microstructures of the welded joints.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.