Several targets are described that in simulations give yields of 1–30 MJ when indirectly driven by 0.9–2 MJ of 0.35 μm laser light. The article describes the targets, the modeling that was used to design them, and the modeling done to set specifications for the laser system in the proposed National Ignition Facility. Capsules with beryllium or polystyrene ablators are enclosed in gold hohlraums. All the designs utilize a cryogenic fuel layer; it is very difficult to achieve ignition at this scale with a noncryogenic capsule. It is necessary to use multiple bands of illumination in the hohlraum to achieve sufficiently uniform x-ray irradiation, and to use a low-Z gas fill in the hohlraum to reduce filling of the hohlraum with gold plasma. Critical issues are hohlraum design and optimization, Rayleigh–Taylor instability modeling, and laser–plasma interactions.

Several inertial confinement fusion (ICF) capsule designs have been proposed as possible candidates for achieving ignition by indirect drive on the National Ignition Facility (NIF) laser [Paisner et al., Laser Focus World 30, 75 (1994)]. This article reviews these designs, their predicted performance using one-, two-, and three-dimensional numerical simulations, and their fabricability. Recent design work at a peak x-ray drive temperature of 250 eV with either 900 or 1300 kJ total laser energy confirms earlier capsule performance estimates [Lindl, Phys. Plasmas 2, 3933 (1995)] that were based on hydrodynamic stability arguments. These simulations at 250 eV and others at the nominal 300 eV drive show that capsules having either copper doped beryllium (Be+Cu) or polyimide (C22H10N2O4) ablators have favorable implosion stability and material fabrication properties. Prototypes of capsules using these ablator materials are being constructed using several techniques: brazing together machined hemishells (Be+Cu), sputter deposition (Be+Cu), and monomer deposition followed by thermal processing (polyimide).

Details of schemes for two tabletop size x-ray lasers that require a high-intensity short-pulse driving laser are discussed. The first is based on rapid recombination following optical-field ionization. Analytical and numerical calculations of the output properties are presented. Propagation in the confocal geometry is discussed and a solution for x-ray lasing in Li-like N at 247 A is described. Since the calculated gain coefficient depends strongly on the electron temperature, the methods of calculating electron heating following field ionization are discussed. Recent experiments aimed at demonstrating lasing in H-like Li at 135 A are discussed along with modeling results. The second x-ray laser scheme is based on the population inversion obtained during inner-shell photoionization by hard x rays. This approach has significantly higher-energy requirements, but lasing occurs at very short wavelengths (..1.<15 A). Experiments that are possible with existing lasers are discussed.

Simulations indicate dramatically reduced growth of short wavelength hydrodynamic instabilities, resulting from two changes in the designs. First, better optimization results from systematic mapping of the ignition target performance over the parameter space of ablator and fuel thickness combinations, using techniques developed by one of us (Herrmann). After the space is mapped with one-dimensional simulations, exploration of it with two-dimensional simulations quantifies the dependence of instability growth on target dimensions. Low modes and high modes grow differently for different designs, allowing a trade-off of the two regimes of growth. Significant improvement in high-mode stability can be achieved, relative to previous designs, with only insignificant increase in low-mode growth. This procedure produces capsule designs that, in simulations, tolerate several times the surface roughness that could be tolerated by capsules optimized by older more heuristic techniques. Another significant reduction in instability growth, by another factor of several, is achieved with ablators with radially varying dopant. In this type of capsule the mid-Z dopant, which is needed in the ablator to minimize xray preheat at the ablator-ice interface, is optimally positioned within the ablator. A fabrication scenario for graded dopants already exists, using sputter coating to fabricate the ablator shell. We describe the systematics of these advances in capsule design, discuss the basis behind their improved performance, and summarize how this is affecting our plans for NIF ignition.

No abstract