This paper presents magnetic properties of highly ordered ultrathin FeRh films deposited on Si/SiO wafers with MgO as a buffer layer. The antiferromagnetic to ferromagnetic (FM) transition is observed with a thickness as low as 3 nm. However, as the thickness decreases, the residual magnetization (M rs ) at low temperature increases and the amplitude of the transition decreases. In addition, the transition becomes much broader for the thinner films. This broadening is related to the grain size reduction in the thinner films. The temperature dependence of the magnetization of a highly ordered B2 FeRh film with a thickness of 10 nm was carefully measured as a function of field. The results show that the transition temperature decreases almost linearly with a rate of 0.93 K/kOe (heating) and 0.97 K/kOe (cooling) close to the value for the bulk samples, while M rs obtained at 100 K increases rapidly at low field and then linearly at a field larger than 10 kOe, which clearly demonstrates that an applied field would induce FM stabilization in ultrathin FeRh films. 3 For these applications, FeRh film is used to reduce the switching field of the storage layer through the exchange coupling between the ferromagnetic (FM) FeRh layer and the storage layer at elevated temperatures without sacrificing the thermal stability of the storage layer at ambient temperature, since the antiferromagnetic (AF) FeRh layer provides negligible exchange coupling to the storage layer. The major challenge is to prepare ultrathin FeRh films with a single AF phase at ambient temperature, which will convert to the FM phase at elevated temperatures, and vice versa. So far, a sharp AF-FM transition of FeRh film was only reported at a thickness above 14 nm. 4 For ultrathin films with a thickness of 10 nm or below, a large residual magnetization (M rs ) is generally observed. 5 The origin of this low temperature FM phase remains unclear. Fan et al.6 observed the existence of a FM phase in a region within 6-8 nm near the top and bottom interfaces of a FeRh film. Based on ab initio calculations, Lounis et al.7 found that a FM state is stable up to 9 atomic layers for Rh-terminated FeRh films. In addition, the AF structure would become unstable when the amount of the site-exchange defect density exceeds a threshold of 0.8%/f.u. 8 Furthermore, based on the phase diagram, 9 the AF to FM transition can be only achieved in the a 00 phase which is formed within a narrow Fe atomic concentration range from 45% to 51%. Due to slow diffusion rate of Rh, it is likely that a mixture of the FM Ferich a 0 phase and the paramagnetic Rh-rich c phase is formed in the film. In this paper, the magnetic stability of ultrathin (10 nm) FeRh films is examined. It is found that for such ultrathin FeRh films, the low temperature FM stabilization is sensitive to the film thickness and the applied magnetic field. An AF to FM transition is observed at a thickness as low as 3 nm, which is close to the FM stabilization thickness based on ab initio calculations for Rh-terminated fi...

Mn1.4Ga films with high perpendicular magnetic anisotropy and high crystalline quality were grown on MgO substrates with Cr buffer layer using molecular beam epitaxy. The crystalline structure and the surface morphology of the films have been systematically investigated as functions of in-situ annealing temperature (Ta) and film thickness. It is found that the magnetic properties can be largely tuned by adjusting Ta. As Ta increases, both saturation magnetization (Ms) and uniaxial perpendicular magnetic anisotropy constant (Ku) increase to the maximum values of 612 emu/cc and 18 Merg/cc at 300 °C, respectively, and then decrease. The morphology also changes with Ta, showing a minimum roughness of 2.2 Å at Ta = 450 °C. On the other hand, as the thickness increases, Ms and Ku increase while coercivity decreases, which indicates there is a magnetic dead layer with a thickness of about 1.5 nm at the interfaces. The detailed examination on the surface morphology of the films with various thicknesses shows a complicated film growth process, which can be understood from the relaxation mechanism of the interfacial strain.

Highly ordered B2 FeRh films with sharp magnetic transitions from the antiferromagnetic (AF) to ferromagnetic (FM) states were prepared on thermally oxidized Si wafers with thicknesses as low as 10 nm. It is found that the transition temperature increases as the thickness decreases from 80 nm to 15 nm, and then decreases from 15 nm to 10 nm. While the ratio of the residual magnetization to the maximum magnetization keeps nearly unchanged for the film thickness of 15 nm and larger, it increases significantly when the thickness is reduced to 10 nm. This residual magnetization was suppressed by slightly increasing the Rh atomic content in 10 nm thick FeRh films. Low-pressure deposition is found to play an important role in the stabilization of the AF phase. By depositing FeRh films at an extremely low pressure of 0.057 Pa, a residual magnetization as small as 13.5 emu/cc at 100 K was observed for a film with a nominal thickness of 10 nm deposited on Si wafer. This value was further reduced to 6 emu/cc when the film is deposited on MgO substrates due to much improved FeRh crystallinity. These results are in close agreement with theoretical predictions on defect and interface induced FM stabilization.