No abstract

We demonstrated high-performance gas sensors based on graphene oxide (GO) sheets partially reduced via low-temperature thermal treatments. Hydrophilic graphene oxide sheets uniformly suspended in water were first dispersed onto gold interdigitated electrodes. The partial reduction of the GO sheets was then achieved through low-temperature, multi-step annealing (100, 200, and 300 degrees C) or one-step heating (200 degrees C) of the device in argon flow at atmospheric pressure. The electrical conductance of GO was measured after each heating cycle to interpret the level of reduction. The thermally-reduced GO showed p-type semiconducting behavior in ambient conditions and was responsive to low-concentration NO2 and NH3 gases diluted in air at room temperature. The sensitivity can be attributed mainly to the electron transfer between the reduced GO and adsorbed gaseous molecules (NO2/NH3). Additionally, the contact between GO and the Au electrode is likely to contribute to the overall sensing response because of the adsorbates-induced Schottky barrier variation. A simplified model is used to explain the experimental observations.

A highly sensitive and selective field‐effect transistor biosensor using thermally reduced graphene oxide (TRGO) sheet decorated with gold nanoparticle‐antibody conjugates is demonstrated. Probe antibody (anti‐Immunoglobulin G) is labeled on the surface of the TRGO sheet through gold nanoparticles and electrical detection of the protein binding (Immunoglobulin G and anti‐Immunoglobulin G) is accomplished by FET and dc measurements.

We demonstrate a high-performance gas sensor using partially reduced graphene oxide ͑GO͒ sheets obtained through low-temperature step annealing ͑300°C at maximum͒ in argon flow at atmospheric pressure. The electrical conductance of GO was measured after each heating cycle to interpret the level of reduction. The thermally reduced GO showed p-type semiconducting behavior in ambient conditions and were responsive to low-concentration NO 2 diluted in air at room temperature. The sensitivity is attributed to the electron transfer from the reduced GO to adsorbed NO 2 , which leads to enriched hole concentration and enhanced electrical conduction in the reduced GO sheet.

Graphene is worth evaluating for chemical sensing and biosensing due to its outstanding physical and chemical properties. We first report on the fabrication and characterization of gas sensors using a back-gated field-effect transistor platform with chemically reduced graphene oxide (R-GO) as the conducting channel. These sensors exhibited a 360% increase in response when exposed to 100 ppm NO(2) in air, compared with thermally reduced graphene oxide sensors we reported earlier. We then present a new method of signal processing/data interpretation that addresses (i) sensing devices with long recovery periods (such as required for sensing gases with these R-GO sensors) as well as (ii) device-to-device variations. A theoretical analysis is used to illuminate the importance of using the new signal processing method when the sensing device suffers from slow recovery and non-negligible contact resistance. We suggest that the work reported here (including the sensor signal processing method and the inherent simplicity of device fabrication) is a significant step toward the real-world application of graphene-based chemical sensors.

Meeting the increasing demand for sensors with high sensitivity, high selectivity, and rapid detection presents many challenges. In the last decade, electronic sensors based on field-effect transistors (FETs) have been widely studied due to their high sensitivity, rapid detection, and simple test procedure. Among these sensors, two-dimensional (2D) nanomaterial-based FET sensors have been demonstrated with tremendous potential for the detection of a wide range of analytes which is attributed to the unique structural and electronic properties of 2D nanomaterials. This comprehensive review discusses the recent progress in graphene-, 2D transition metal dichalcogenide-, and 2D black phosphorus-based FET sensors, with an emphasis on rapid and low-concentration detection of gases, biomolecules, and water contaminants.

A new gas‐sensing platform for low‐concentration gases (NO2, H2, and CO) comprises discrete SnO2 nanocrystals uniformly distributed on the surface of multiwalled carbon nanotubes (CNTs). The resulting hybrid nanostructures are highly sensitive, even at room temperature, because their gas sensing abilities rely on electron transfer between the nanocrystals and the CNTs.

Crumpled graphene oxide (GO)/graphene is a new type of carbon nanostructure that has drawn growing attention due to its three-dimensional open structure and excellent stability in an aqueous solution. Here we report a general and one-step approach to produce crumpled graphene (CG)-nanocrystal hybrids, which are produced by direct aerosolization of a GO suspension mixed with precursor ions. Nanocrystals spontaneously grow from precursor ions and assemble on both external and internal surfaces of CG balls during the solvent evaporation and GO crumpling process. More importantly, CG-nanocrystal hybrids can be directly deposited onto various current-collecting substrates, enabling their tremendous potential for energy applications. As a proof of concept, we demonstrate the use of hybrid electrodes of CG-Mn(3)O(4) and CG-SnO(2) in an electrochemical supercapacitor and a lithium-ion battery, respectively. The performance of the resulting capacitor/battery is attractive and outperforms conventional flat graphene-based hybrid devices. This study provides a new and facile route to fabricating high-performance hybrid CG-nanocrystal electrodes for various energy systems.