The optical, structural, and electrical properties of thin layers made from poly(3‐hexylthiophene) (P3HT) samples of different molecular weights are presented. As reported in a previous paper by Kline et al., Adv. Mater. 2003, 15, 1519, the mobilities of these layers are a strong function of the molecular weight, with the largest mobility found for the largest molecular weight. Atomic force microscopy studies reveal a complex polycrystalline morphology which changes considerably upon annealing. X‐ray studies show the occurrence of a layered phase for all P3HT fractions, especially after annealing at 150 °C. However, there is no clear correlation between the differences in the transport properties and the data from structural investigations. In order to reveal the processes limiting the mobility in these layers, the transistor properties were investigated as a function of temperature. The mobility decreases continuously with increasing temperatures; with the same trend pronounced thermochromic effects of the P3HT films occur. Apparently, the polymer chains adopt a more twisted, disordered conformation at higher temperatures, leading to interchain transport barriers. We conclude that the backbone conformation of the majority of the bulk material rather than the crystallinity of the layer is the most crucial parameter controlling the charge transport in these P3HT layers. This interpretation is supported by the significant blue‐shift of the solid‐state absorption spectra with decreasing molecular weight, which is indicative of a larger distortion of the P3HT backbone in the low‐molecular weight P3HT layers.

The fact that organic solar cells perform efficiently despite the low dielectric constant of most photoactive blends initiated a long-standing debate regarding the dominant pathways of free charge formation. Here, we address this issue through the accurate measurement of the activation energy for free charge photogeneration over a wide range of photon energy, using the method of time-delayed collection field. For our prototypical low bandgap polymer:fullerene blends, we find that neither the temperature nor the field dependence of free charge generation depend on the excitation energy, ruling out an appreciable contribution to free charge generation though hot carrier pathways. On the other hand, activation energies are on the order of the room temperature thermal energy for all studied blends. We conclude that charge generation in such devices proceeds through thermalized charge transfer states, and that thermal energy is sufficient to separate most of these states into free charges.

No abstract

Aggregation of chromophores in the solid state commonly causes undesirable red shifts in the emission spectra and/or emission quenching. To overcome this problem, we have prepared soluble perylenetetracarboxidiimide dyes in which the chromophores are effectively shielded by polyphenylene dendrimers attached in the bay positions. Models show that attachment of the shielding units in the bay position should provide more efficient shielding than attaching them via the imide moieties. The dendrimers possess excellent film-forming properties due to alkyl substituents on their peripheries. The lack of a red shift in emission upon going from solution to the solid state indicates the dendrons suppress interaction of the emissive cores, leading to pure red-orange emission. Single-layer LEDs produce red-orange emission with relatively low efficiency especially for the higher generation dendrons, which is attributed to poor charge conduction. LEDs using blends of the dendrimers and the undendronized dye as a model compound in PVK have been investigated, and a model to extract relative charge injection rates through the dendritic scaffold from the spectral contributions in the EL spectra is developed.

We report that the performances of blue polymer electrophosphorescent devices are crucially depending on the choice of the electron transporting material incorporated into the emissive layer. Devices with 1,3-bis[(4-tert-butylphenyl)-1,3,4-oxidiazolyl]phenylene (OXD-7) doped at ∼40wt% into a poly(vinylcarbazole) matrix exhibited significantly higher efficiencies than those with 2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD), yielding maximum luminous and power efficiency values of 18.2 Cd∕A and 8.8 lm∕W, respectively. Time resolved photoluminescence measurements revealed a long lifetime phosphorescence component in layers with PBD, which we assign to significant triplet harvesting by this electron-transporting component.

In order to unravel the intricate interplay between disorder effects, molecular reorganization, and charge carrier localization, a comprehensive study was conducted on hole transport in a series of conjugated alternating phenanthrene indenofluorene copolymers. Each polymer in the series contained one further comonomer comprising monoamines, diamines, or amine-free structures, whose influence on the electronic, optical, and charge transport properties was studied. The series covered a wide range of highest occupied molecular orbital (HOMO) energies as determined by cyclovoltammetry. The mobility, inferred from time-of-flight (ToF) experiments as a function of temperature and electric field, was found to depend exponentially on the HOMO energy. Since possible origins for this effect include energetic disorder, polaronic effects, and wave function localization, the relevant parameters were determined using a range of methods. Disorder and molecular reorganization were established first by an analysis of absorption and emission measurements and second by an analysis of the ToF measurements. In addition, density functional theory calculations were carried out to determine how localized or delocalized holes on a polymer chain are and to compare calculated reorganization energies with those that have been inferred from optical spectra. In summary, we conclude that molecular reorganization has little effect on the hole mobility in this system while both disorder effects and hole localization in systems with low-lying HOMOs are predominant. In particular, as the energetic disorder is comparable for the copolymers, the absolute value of the hole mobility at room temperature is determined by the hole localization associated with the triarylamine moieties.

The spectral characteristics of polyfluorene (PF)‐based light‐emitting diodes (LEDs) containing a defined low concentration of either keto‐defects or of the polymer poly(9,9‐octylfluorene‐co‐benzothiadiazole) (F8BT) are presented. Both types of blend layers were tested in different device configurations with respect to the relative and absolute intensities of green and blue emission components. It is shown that blending hole‐transporting molecules into the emission layer at low concentration or incorporation of a suitable hole‐transporting layer reduces the green emission contribution in the electroluminescence (EL) spectrum of the PF:F8BT blend, which is similar to what is observed for the keto‐containing PF layer. We conclude that the keto‐defects in PF homopolymer layers mainly constitute weakly emissive electron traps, in agreement with the results of quantum‐mechanical calculations.

Perovskite semiconductors have demonstrated outstanding external luminescence quantum yields, enabling high power conversion efficiencies (PCEs). However, the precise conditions to advance to an efficiency regime above monocrystalline silicon cells are not well understood. Herein, a simulation model that describes efficient p–i–n‐type perovskite solar cells well and a range of different experiments is established. Then, important device and material parameters are studied and it is found that an efficiency regime of 30% can be unlocked by optimizing the built‐in voltage across the perovskite layer using either highly doped (1019 cm−3) transport layers (TLs), doped interlayers or ultrathin self‐assembled monolayers. Importantly, only parameters that have been reported in recent literature are considered, that is, a bulk lifetime of 10 μs, interfacial recombination velocities of 10 cm s−1, a perovskite bandgap ( E gap ) of 1.5 eV, and an external quantum efficiency (EQE) of 95%. A maximum efficiency of 31% is predicted for a bandgap of 1.4 eV. Finally, it is demonstrated that the relatively high mobile ion density does not represent a significant barrier to reach this efficiency regime. The results of this study suggest continuous PCE improvements until perovskites may become the most efficient single‐junction solar cell technology in the near future.