Bees are very important for terrestrial ecosystems and, above all, for the subsistence of many crops, due to their ability to pollinate flowers. Currently, the honey bee populations are decreasing due to colony collapse disorder (CCD). The reasons for CCD are not fully known, and as a result, it is essential to obtain all possible information on the environmental conditions surrounding the beehives. On the other hand, it is important to carry out such information gathering as non-intrusively as possible to avoid modifying the bees’ work conditions and to obtain more reliable data. We designed a wireless-sensor networks meet these requirements. We designed a remote monitoring system (called WBee) based on a hierarchical three-level model formed by the wireless node, a local data server, and a cloud data server. WBee is a low-cost, fully scalable, easily deployable system with regard to the number and types of sensors and the number of hives and their geographical distribution. WBee saves the data in each of the levels if there are failures in communication. In addition, the nodes include a backup battery, which allows for further data acquisition and storage in the event of a power outage. Unlike other systems that monitor a single point of a hive, the system we present monitors and stores the temperature and relative humidity of the beehive in three different spots. Additionally, the hive is continuously weighed on a weighing scale. Real-time weight measurement is an innovation in wireless beehive—monitoring systems. We designed an adaptation board to facilitate the connection of the sensors to the node. Through the Internet, researchers and beekeepers can access the cloud data server to find out the condition of their hives in real time.

Public lighting represents a large part of the energy consumption of towns and cities. Efficient management of public lighting can entail significant energy savings. This work presents a smart system for managing public lighting networks based on wireless communication and the DALI protocol. Wireless communication entails significant economic savings, as there is no need to install new wiring and visual impacts and damage to the facades of historical buildings in city centers are avoided. The DALI protocol uses bidirectional communication with the ballast, which allows its status to be controlled and monitored at all times. The novelty of this work is that it tackles all aspects related to the management of public lighting: a standard protocol, DALI, was selected to control the ballast, a wireless node based on the IEEE 802.15.4 standard with a DALI interface was designed, a network layer that considers the topology of the lighting network has been developed, and lastly, some user-friendly applications for the control and maintenance of the system by the technical crews of the different towns and cities have been developed.

Precision agriculture can be defined as the science of using technology to improve the agricultural production. It is advisable for farmers to use a decision support system; in fact, real–time monitoring of climatic conditions is the only way to know the water needed by a cultivation. On the other hand, since the 1990s, a strong decrease of the Mediterranean Quercus has been observed in the pastures of southwestern Spain and Portugal, causing a high mortality of holm and cork oak trees. Among the factors associated with this decrease, the radical decomposition caused by Phytophthora Cinnamomi is remarkable for its gravity, which makes it necessary to reforest the trees and to monitor the microclimatic factors that have an influence on this regeneration. Wireless Sensor Networks (WSN) are a technology in full evolution and development, as well as their appropriate use in cultivations that help to implement ecological techniques. With these considerations in this work five units/nodes with one or more sensors that allow different environmental readings have been developed. In this work, the acquisition of data obtained from different sensors has been achieved, allowing the monitoring of climatic elements such as soil moisture, air quality, temperature and humidity, rainfall intensity, precipitation level, wind speed and direction, luminous flux and atmospheric pressure. A web page has been designed where the user can consult the climatic conditions of the cultivation or reforestation. Different devices interconnected with a central unit have been developed where measurements of the cultivation are sent for its later analysis by the farmer. The microclimatic data acquisition developed in the WSN proposed in this paper allows a farmer to make decisions about the irrigation of the cultivation, use of fertilizers, the development and maturation phases of the cultivated products, obtaining the optimum stages of cultivation and harvesting.

More and more human activities are increasingly dependent on the power quality energy they are supplied. In particular, those loads that have an electronic switching mode power supply (SMPS) and microcontrollers or microprocessors are very susceptible to de-energization of the AC line as voltage monitoring takes place on the DC end and may not have enough time to cope with a voltage event involving energy loss. There have been many proposals that analyze power quality or current consumption, even those using limited resources hardware or the classic formulas of discrete root mean square (RMS). In this proposal, an approximation to the problem by means of an RMS value estimator that uses as a base a microcontroller of basic range and low economic cost and algorithms of calculation of very low computational cost that elude complex arithmetic operation to controllers, such as powers or roots, is presented. The results of the experiments to which the proposal was subjected show its ability to provide an estimation of the RMS value of voltage with sufficient precision or an event alarm in less time than the options analyzed. The validation tests and functional comparison of the prototype which were carried out support its viability.

In this study, the Wbee Sensor System was used to record data from 10 Iberian beehives for two years in southern Spain. These data were used to identify potential conditioning climatic factors of the internal regulatory behavior of the hive and its weight. Categorical principal components analysis (CATPCA) was used to determine the minimum number of those factors able to capture the maximum percentage of variability in the data recorded. Then, categorical regression (CATREG) was used to select the factors that were linearly related to hive internal humidity, temperature and weight to issue predictive regression equations in Iberian bees. Average relative humidity values of 51.7% ± 10.4 and 54.2% ± 11.7 were reported for humidity in the brood nest and in the food area, while average temperatures were 34.3 °C ± 1.5 in the brood nest and 29.9 °C ± 5.8 in the food area. Average beehive weight was 38.2 kg ± 13.6. Some of our data, especially those related to humidity, contrast with previously published results for other studies about bees from Central and northern Europe. Conclusively, certain combinations of climatic factors may condition within hive humidity, temperature and hive weight. Southern Iberian honeybees’ brood nest humidity regulatory capacity could be lower than brood nest thermoregulatory capacity, maintaining values close to 34 °C, even in dry conditions.

Smart lighting systems based on the Digital Addressable Lighting Interface (DALI) protocol are the most suitable for street lighting systems, allowing digital lighting control operations. Unfortunately, the microcontrollers, which are commonly used in the Wireless Sensor Network nodes to control the lamps, do not implement this protocol. The DALI protocol implemented by software in the microcontroller consumes hardware resources (timers), processing time and requires a precise temporal analysis of the application, due to the strict bit times and the Manchester coding that it uses. In this work, the design of a bridge is proposed to free the microcontroller from the implementation of the DALI protocol. The novelty of this work is the implementation of the DALI Bridge in a low-cost Field-Programmable Gate Array (FPGA) with low power consumption. The bridge has been described in the hardware description language following the 1076-93 and 1076.3-97 standards, to guarantee its portability. The results of the synthesis show that a minimum amount of logical and routing resources is used, that the power consumption is in the order of tens of mW, that it has a very small latency time and that it supports a high operating frequency, which allows adding new functions. Its operation is verified by implementing a wireless sensor node using an FPGA of the Lattice Semiconductor iCE40 family.

No abstract

No abstract