Soybean is a major legume crop originating in temperate regions, and photoperiod responsiveness is a key factor in its latitudinal adaptation. Varieties from temperate regions introduced to lower latitudes mature early and have extremely low grain yields. Introduction of the long-juvenile (LJ) trait extends the vegetative phase and improves yield under short-day conditions, thereby enabling expansion of cultivation in tropical regions. Here we report the cloning and characterization of J, the major classical locus conferring the LJ trait, and identify J as the ortholog of Arabidopsis thaliana EARLY FLOWERING 3 (ELF3). J depends genetically on the legume-specific flowering repressor E1, and J protein physically associates with the E1 promoter to downregulate its transcription, relieving repression of two important FLOWERING LOCUS T (FT) genes and promoting flowering under short days. Our findings identify an important new component in flowering-time control in soybean and provide new insight into soybean adaptation to tropical regions.

Primordial black holes and secondary gravitational waves can be used to probe the small scale physics at very early time. For secondary gravitational waves produced after the horizon reentry, we derive an analytical formula for the time integral of the source and analytical behavior of the time dependence of the energy density of induced gravitational waves is obtained. By proposing a piecewise power law parametrization for the power spectrum of primordial curvature perturbations, we use the observational constraints on primordial black hole dark matter to obtain an upper bound on the power spectrum, and discuss the test of the model with future space based gravitational wave antenna.

No abstract

No abstract

To alleviate the stress of continuous cropping for cucumber continuous cropping (CCC) system, a beneficial fungus Trichoderma harzianum SQR-T037 (SQR-T037) was isolated and applied to soil to degrade allelochemicals exuded from cucumber plants in a Rhizobox experiment. The following phenolic acids (PAs), classified as allelochemicals, were isolated and identified from cucumber rhizospheres: 4-hydroxybenzoic acid, vanillic acid, ferulic acid, benzoic acid, 3-phenylpropionic acid, and cinnamic acid. Mixed PAs added in potato dextrose broth, each with 0.2 gram per liter, were completely degraded by SQR-T037 after 170 h of incubation. In Rhizobox experiments, inoculation of SQR-T037 in the CCC soil also degraded the PAs exuded from cucumber plant roots. This degradation was 88.8% for 4-hydroxybenzoic acid, 90% for vanillic acid, 95% for benzoic acid, and 100% for ferulic acid, 3-phenylpropionic acid, and cinnamic acid at 45 days after plantation. Simultaneously, a significant (p ≥ 0.05) decrease in the disease index of Fusarium wilt and an increase in dry weights of cucumber plants were obtained in pot experiments by application of SQR-T037. This was mostly attributed to degradation of PAs exuded from cucumber roots in CCC soil by SQR-T037 and alleviation of the allelopathic stress. Application of beneficial microorganisms, such as SQR-T037 that biodegrades allelochemicals, is a highly efficient way to resolve the problems associated with continuous cropping system.

No abstract

In grasslands, forage and livestock production results in soil nutrient deficits as grasslands typically receive no nutrient inputs, leading to a loss of grassland biomass. The application of mature compost has been shown to effectively increase grassland nutrient availability. However, research on fertilization regime influence and potential microbial ecological regulation mechanisms are rarely conducted in grassland soil. We conducted a two-year experiment in meadow steppe grasslands, focusing on above- and belowground consequences of organic or Trichoderma biofertilizer applications and potential soil microbial ecological mechanisms underlying soil chemistry and microbial community responses. Grassland biomass significantly (p = 0.019) increased following amendment with 9,000 kg ha−1 of Trichoderma biofertilizer (composted cattle manure + inoculum) compared with other assessed organic or biofertilizer rates, except for BOF3000 (fertilized with 3,000 kg ha−1 biofertilizer). This rate of Trichoderma biofertilizer treatment increased soil antifungal compounds that may suppress pathogenic fungi, potentially partially responsible for improved grassland biomass. Nonmetric multidimensional scaling (NMDS) revealed soil chemistry and fungal communities were all separated by different fertilization regime. Trichoderma biofertilizer (9,000 kg ha−1) increased relative abundances of Archaeorhizomyces and Trichoderma while decreasing Ophiosphaerella. Trichoderma can improve grassland biomass, while Ophiosphaerella has the opposite effect as it may secrete metabolites causing grass necrosis. Correlations between soil properties and microbial genera showed plant-available phosphorus may influence grassland biomass by increasing Archaeorhizomyces and Trichoderma while reducing Ophiosphaerella. According to our structural equation modeling (SEM), Trichoderma abundance was the primary contributor to aboveground grassland biomass. Our results suggest Trichoderma biofertilizer could be an important tool for management of soils and ultimately grassland plant biomass.

Permanent magnet synchronous machines (PMSMs) can provide excellent performance in terms of torque density, energy efficiency and controllability. However, PMs on the rotor are prone to the centrifugal force which may break their physical integrity, especially at high-speed operation. Typically, PMs are bound with carbon fiber or retained by alloy sleeves on the rotor surface. This paper is concerned with the design of a rotor retaining sleeve for a 1.12-MW 18-krpm PM machine; its electromagnetic performance is investigated by the 2D finite element method (FEM). Theoretical and numerical analysis of the rotor stress are carried out. For the carbon fiber protective measure, the stresses of three PM configurations and three pole filler materials are compared in terms of operating temperature, rotor speed, retaining sleeve thickness, and interference fit. Then a new hybrid protective measure is proposed and analyzed by the 2D FEM for operational speeds up to 22 krpm (1.2 times the rated). The rotor losses and machine temperatures with the carbon fiber retaining sleeve and the hybrid retaining sleeve are compared and the sleeve design is refined. Two rotors using both designs are prototyped and experimentally tested to validate the effectiveness of the developed techniques for permanent magnet machines. The developed retaining sleeve makes it possible to operate MW PM machines at high speeds of 22 krpm. This opens doors for many high-power high-speed applications such as turbo-generators, aerospace and submarine motor drives.