Maleic anhydride (MA) is incorporated into poly(lactic acid) (PLA)/poly(propylene carbonate) (PPC) blends to modify its properties through melt compounding. It is interesting to note that the toughness of PLA/PPC blends can be improved by 1355% while the strength is almost kept constant by adding very low content (as low as 0.9%) of MA into the blends. However, higher MA content in the blends leads to decrease in strength and further increase in toughness indicating an obvious plasticizing effect, while MA is shown to have no effect on the toughness of neat PLA. Rheological, scanning electron microscopy (SEM) and dynamic mechanical analysis (DMA) studies have been carried out to understand the above results. It is believed that the improvement in mechanical performance originated from the largely retained molecular weight of PPC and improved interfacial interaction after processing. And relative large amount of MA in the blends is shown to mainly plasticize the PPC phase rather than the PLA phase. Such an effective method could provide PLA based biodegradable polymer blends with novel properties for industrial applications

The formation of a shish kebab (SK) structure, where carbon nanotubes (CNTs) serve as shish and polymer lamellae serve as kebab, is particularly interesting and provides a novel way to enhance the polymer-CNT interface. A fine SK structure is achieved through melt spinning. High density polyethylene and pristine CNTs were first compounded in an extruder. The compound was then spun into fibers with different draw ratios with the aid of a capillary rheometer. The crystalline structure and mechanical behavior were characterized by scanning electron microscopy, differential scanning calorimetry, two-dimensional wide-angle X-ray scattering, polarized Raman spectroscopy, and tensile testing. An increase in tensile strength as high as 3 times has been achieved in the fiber. The formation of SKs is considered as the main mechanism responsible for the enhanced interfacial interaction and excellent tensile property.

To extend the application of a carbon dioxide sourced environmental friendly polymer: poly (propylene carbonate) (PPC), a small amount of maleic anhydride (MA) was melt blended to end-cap with PPC to improve its thermal stability and mechanical properties. Thermal and mechanical properties of end-capped PPC were investigated by TGA, GPC, mechanical test, and DMA. TGA and titration results demonstrate that PPC can be easily end-capped with MA through simple melt blending. TGA results show that the thermal degradation temperature of PPC could be improved by around 140 C by adding MA. GPC measurement indicates that the molecular weight of PPC can be maintained after blending with MA, where pure PPC experiences a dramatic degradation in molecular weight during melt process. More importantly, the tensile strength of PPC after blending with MA was found to be nearly eight times higher than that of pure PPC. It has approached the mechanical properties of polyolefin polymers, indicating the possibility of replacing polyolefin polymers with PPC for low temperature applications. The method described here could be used to extend the applications of PPC and fight against the well known global warming problem.

Abstract:The influence of solid-state drawing on the morphology of melt-spun poly(L-lactic acid) (PLLA) tapes, and the accompanying changes in mechanical and degradation behaviour have been studied. Mechanical properties are found to be strongly dependent on both applied draw ratio and drawing temperature. Moduli of these highly oriented tapes are significantly increased compared to as-extruded tapes at both ambient and elevated temperatures. Interestingly, drawing leads to a significant increase in elongation to break (~3 times) and toughness (~13 times) compared to as-extruded tapes. Structural and morphological characterization indicates strain-induced crystallization as well as an increase in orientation of the crystalline phase at small strains. Upon further stretching, an "overdrawing" regime is observed, with decreased crystalline orientation due to the breakage of existing crystals. For fixed draw ratios, a significant increase in Young's modulus and tensile strength is observed with increasing drawing temperature, due to a higher crystallinity and orientation obtained for tapes drawn at higher temperatures. FT-IR results indicate no crystal transformation after drawing, with the α-form being observed in all tapes. Hydrolytic degradability of PLLA was significantly reduced by solid-state drawing.

No abstract

No abstract

In this work, polyamide 66 (PA66) and its composites with multiwalled carbon nanotubes (MWNTs) were melt spun into fibers at different draw ratios. PA66 fibers at high draw ratio demonstrate a 40% increase in tensile strength, 66% increase in modulus and a considerable increase in toughness. It is demonstrated that this reinforcement can be mainly attributed to high‐draw‐ratio‐induced good dispersion and orientation of MWNTs, particularly the enhanced interfacial adhesion between MWNT and matrix thanks to interfacial crystallization. Our work provides a simple but efficient method to achieve good dispersion and strong interfacial interaction through melt spinning. Copyright © 2011 Society of Chemical Industry

No abstract