In high-pressure turbines, cool air is purged through rim seals at the periphery of wheel-spaces between the stator and rotor disks. The purge suppresses the ingress of hot gas from the annulus but superfluous use is inefficient. In this paper, the interaction between the ingress, purge, and mainstream flow is studied through comparisons of newly acquired experimental results alongside unsteady numerical simulations based on the DLR TRACE solver. New experimental measurements were taken from a one-and-a-half stage axial-turbine rig operating with engine-representative blade and vane geometries, and overlapping rim seals. Radial traverses using a miniature CO2 concentration probe quantified the penetration of ingress into the rim seal and the outer portion of the wheel-space. Unsteady pressure measurements from circumferentially positioned transducers on the stator disk identified distinct frequencies in the wheel-space, and the computations reveal these are associated with large-scale flow structures near the outer periphery rotating at just less than the disk speed. It is hypothesized that the physical origin of such phenomenon is driven by Kelvin–Helmholtz instabilities caused by the tangential shear between the annulus and egress flows, as also postulated by previous authors. The presence and intensity of these rotating structures are strongly dependent on the purge flow rate. While there is general qualitative agreement between experiment and computation, it is speculated that the underprediction by the computations of the measured levels of ingress is caused by deficiencies in the turbulence modeling.

The ingress of hot annulus gas into stator–rotor cavities is an important topic to engine designers. Rim-seals reduce the pressurized purge required to protect highly stressed components. This paper describes an experimental and computational study of flow through a turbine chute seal. The computations—which include a 360 deg domain—were undertaken using dlrtrace's time-marching solver. The experiments used a low Reynolds number turbine rig operating with an engine-representative flow structure. The simulations provide an excellent prediction of cavity pressure and swirl, and good overall agreement of sealing effectiveness when compared to experiment. Computation of flow within the chute seal showed strong shear gradients which influence the pressure distribution and secondary-flow field near the blade leading edge. High levels of shear across the rim-seal promote the formation of large-scale structures at the wheel-space periphery; the number and speed of which were measured experimentally and captured, qualitatively and quantitatively, by computations. A comparison of computational domains ranging from 30 deg to 360 deg indicates that steady features of the flow are largely unaffected by sector size. However, differences in large-scale flow structures were pronounced with a 60 deg sector and suggest that modeling an even number of blades in small sector simulations should be avoided.

This paper presents experimental and computational results using a 1.5-stage test rig designed to investigate the effects of ingress through a double radial overlap rim-seal. The effect of the vanes and blades on ingress was investigated by a series of carefully controlled experiments: first, the position of the vane relative to the rim seal was varied; second, the effect of the rotor blades was isolated using a disk with and without blades. Measurements of steady pressure in the annulus show a strong influence of the vane position. The relationship between sealing effectiveness and purge flowrate exhibited a pronounced inflection for intermediate levels of purge; the inflection did not occur for experiments with a bladeless rotor. Shifting the vane closer to the rim-seal, and therefore the blade, caused a local increase in ingress in the inflection region; again, this effect was not observed for the bladeless experiments. Unsteady pressure measurements at the periphery of the wheel-space revealed the existence of large-scale pressure structures (or instabilities) which depended weakly on the vane position and sealing flowrate. These were measured with and without the blades on the rotor disk. In all cases, these structures rotated close to the disk speed.

In high-pressure turbines, cool air is purged through rim seals at the periphery of wheel-spaces between the stator and rotor discs. The purge suppresses the ingress of hot gas from the annulus but superfluous use is inefficient. In this paper the interaction between the ingress, purge and mainstream flow is studied using unsteady numerical simulations based on the DLR TRACE solver. The computations are compared to experimental measurements from a one-and-a-half stage axial-turbine rig operating with engine-representative blade and vane geometries, and overlapping rim seals. Radial traverses using a miniature CO2 concentration probe quantified the penetration of ingress into the rim seal and the outer portion of the wheel-space. Unsteady pressure measurements from circumferentially-positioned transducers on the stator disc identified distinct frequencies in the wheel-space, and the computations reveal these are associated with large-scale flow structures near the outer periphery rotating at just less than the disc speed. It is hypothesised that the physical origin of such phenomenon is driven by Kelvin-Helmholtz instabilities caused by the tangential shear between the annulus and egress flows, as also postulated by previous authors. The presence and intensity of these rotating structures are strongly dependent on the purge flow rate. While there is general qualitative agreement between experiment and computation, it is speculated that the under-prediction by the computations of the measured levels of ingress is caused by deficiencies in the turbulence modelling.

In gas turbines, rim seals are fitted at the periphery of stator and rotor discs to minimise the purge flow required to seal the wheel-space between the discs. Ingestion (or ingress) of hot mainstream gases through rim seals is a threat to the operating life and integrity of highly-stressed components, particularly in the first-stage turbine. Egress of sealing flow from the first-stage can be re-ingested in downstream stages. This paper presents experimental results using a 1.5-stage test facility designed to investigate ingress into the wheel-spaces upstream and downstream of a rotor disc. Re-ingestion was quantified using measurements of CO2 concentration, with seeding injected into the upstream and downstream sealing flows. Here a theoretical mixing model has been developed from first principles and validated by the experimental measurements. For the first time, a method to quantify the mass fraction of the fluid carried over from upstream egress into downstream ingress has been presented and measured; it was shown that this fraction increased as the downstream sealing flow rate increased. The upstream purge was shown to not significantly disturb the fluid dynamics but only partially mixes with the annulus flow near the downstream seal, with the ingested fluid emanating from the boundary layer on the blade platform. From the analogy between heat and mass transfer, the measured mass-concentration flux is equivalent to an enthalpy flux and this re-ingestion could significantly reduce the adverse effect of ingress in the downstream wheel-space. Radial traverses using a concentration probe in and around the rim seal clearances provide insight into the complex interaction between the egress, ingress and mainstream flows.

Engine designers require accurate predictions of ingestion (or ingress) principally caused by circumferential pressure asymmetry in the mainstream annulus. Cooling air systems provide purge flow designed to limit metal temperatures and protect vulnerable components from the hot gases which would otherwise be entrained into disk cavities through clearances between rotating and static disks. Rim seals are fitted at the periphery of these disks to minimize purge. The mixing between the efflux of purge (or egress) and the mainstream gases near the hub end-wall results in a deterioration of aerodynamic performance. This paper presents experimental results using a turbine test rig with wheel-spaces upstream and downstream of a rotor disk. Ingress and egress was quantified using a CO2 concentration probe, with seeding injected into the upstream and downstream sealing flows. The probe measurements have identified an outer region in the wheel-space and confirmed the expected flow structure. For the first time, asymmetric variations of concentration have been shown to penetrate through the seal clearance and the outer portion of the wheel-space between the disks. For a given flow coefficient in the annulus, the concentration profiles were invariant with rotational Reynolds number. The measurements also reveal that the egress provides a film-cooling benefit on the vane and rotor platforms. Further, these measurements provide unprecedented insight into the flow interaction and provide quantitative data for computational fluid dynamics (CFD) validation, which should help to reduce the use of purge and improve engine efficiency.

In gas turbines, rim seals are fitted at the periphery of stator and rotor discs to minimize the purge flow required to seal the wheel-space between the discs. Ingestion (or ingress) of hot mainstream gases through rim seals is a threat to the operating life and integrity of highly stressed components, particularly in the first-stage turbine. Egress of sealing flow from the first-stage can be re-ingested in downstream stages. This paper presents experimental results using a 1.5-stage test facility designed to investigate ingress into the wheel-spaces upstream and downstream of a rotor disk. Re-ingestion was quantified using measurements of CO2 concentration, with seeding injected into the upstream and downstream sealing flows. Here, a theoretical mixing model has been developed from first principles and validated by the experimental measurements. For the first time, a method to quantify the mass fraction of the fluid carried over from upstream egress into downstream ingress has been presented and measured; it was shown that this fraction increased as the downstream sealing flow rate increased. The upstream purge was shown to not significantly disturb the fluid dynamics but only partially mixes with the annulus flow near the downstream seal, with the ingested fluid emanating from the boundary layer on the blade platform. From the analogy between heat and mass transfer, the measured mass-concentration flux is equivalent to an enthalpy flux, and this re-ingestion could significantly reduce the adverse effect of ingress in the downstream wheel-space. Radial traverses using a concentration probe in and around the rim seal clearances provide insight into the complex interaction between the egress, ingress and mainstream flows.

Engine designers require accurate predictions of ingestion (or ingress) principally caused by circumferential pressure asymmetry in the mainstream annulus. Cooling air systems provide purge flow designed to limit metal temperatures and protect vulnerable components from the hot gases which would otherwise be entrained into disc cavities through clearances between rotating and static discs. Rim seals are fitted at the periphery of these discs to minimise purge. The mixing between the efflux of purge (or egress) and the mainstream gases near the hub end-wall results in a deterioration of aerodynamic performance. This paper presents experimental results using a turbine test rig with wheel-spaces upstream and downstream of a rotor disc. Ingress and egress was quantified using a CO2 concentration probe, with seeding injected into the upstream and downstream sealing flows. The probe measurements have identified an outer region in the wheel-space and confirmed the expected flow structure. For the first time, asymmetric variations of concentration have been shown to penetrate through the seal clearance and the outer portion of the wheel-space between the discs. For a given flow coefficient in the annulus, the concentration profiles were invariant with rotational Reynolds number. The measurements also reveal that the egress provides a film-cooling benefit on the vane and rotor platforms. Further, these measurements provide unprecedented insight into the flow interaction, and provide quantitative data for CFD validation, which should help reduce the use of purge and improve engine efficiency.