In this paper, we propose and numerically analyze a novel design for a high sensitivity refractive index (RI) sensor based on long-range surface plasmon resonance in H-shaped microstructured optical fiber with symmetrical dielectric-metal-dielectric waveguide (DMDW). The influences of geometrical and optical characteristics of the DMDW on the sensor performance are investigated theoretically. A large RI analyte range from 1.33 to 1.39 is evaluated to study the sensing characteristics of the proposed structure. The obtained results show that the DMDW improves the coupling between the fiber core mode and the plasmonic mode. The best configuration shows 27 nm of full width at half maximum with a resolution close to 1.3 × 10 −5 nm, a high sensitivity of 7540 nm/RIU and a figure of merit of 280 RIU −1 . Additionally, the proposed device has potential for multi-analyte sensing and self-reference when dissimilar DMDWs are deposited on the inner walls of the side holes. The proposed sensor structure is simple and presents very competitive sensing parameters, which demonstrates that this device is a promising alternative and could be used in a wide range of application areas.

A highly sensitive temperature sensor based on an all-fiber Sagnac loop interferometer combined with metal-filled side-hole photonic crystal fiber (PCF) is proposed and demonstrated. PCFs containing two side holes filled with metal offer a structure that can be modified to create a change in the birefringence of the fiber by the expansion of the filler metal. Bismuth and indium were used to examine the effect of filler metal on the temperature sensitivity of the fiber-optic temperature sensor. It was found from measurements that a very high temperature sensitivity of -9.0  nm/°C could be achieved with the indium-filled side-hole PCF. The experimental results are compared to numerical simulations with good agreement. It is shown that the high temperature sensitivity of the sensor is attributed to the fiber microstructure, which has a significant influence on the modulation of the birefringence caused by the expansion of the metal-filled holes.

This work presents a non-invasive, reusable and submersible permittivity sensor that uses a microwave technique for the dielectric characterization of liquid materials. The proposed device consists of a compact split ring resonator excited by two integrated monopole antennas. The sensing principle is based on the notch introduced by the resonators in the transmission coefficient, which is affected due to the introduction of the sensor in a new liquid material. Then, a frequency shift of the notch and the Q-factor of the proposed sensor are related with the changes in the surrounding medium. By means of a particular experimental procedure, commercial liquids are employed to obtain the calibration curve. Thus, a mathematical equation is obtained to extract the dielectric permittivity of liquid materials with unknown dielectric properties. A good match between simulated and experimental results is obtained, as well as a high Q-factor, compact size, good sensitivity and high repeatability for use in sensing applications. Sensors like the one here presented could lead to promising solutions for characterizing materials, particularly in determining material properties and quality in the food industry, bio-sensing and other applications.

We present the design of a porous-core PCF with elliptical holes in the core that achieved low loss, high birefringence, and flattened dispersion for guiding terahertz waves. The finite element method is used to study the properties of the designed waveguide in detail: effective material loss, birefringence, confinement losses, and dispersion. Simulation results show that the proposed structure exhibits simultaneously high modal birefringence of 1.32 × 10 −2 and a flattened dispersion over a broadband of 1.28 THz. Then, polarization splitters, based on both symmetric and asymmetric porous-core PCF structures, are designed and evaluated at 1 THz. We show that this kind of device exhibits a strong polarization-dependent coupling behavior. Numerical results show that the configuration based on dual-core waveguide with asymmetric cores can achieve a 10.9 cm long splitter with a broadband of 0.306 THz for x-polarization and 0.23 THz for y-polarization. Finally, this paper offers an effective method to design an ultrawideband polarization beam splitter to operate in the THz region, which might be relevant for future applications in technical areas, such as spectroscopy, sensing, and high-speed data transmission.

We present a sensing architecture consisting of a two-core chirped microstructured optical fiber (MOF) for refractive index sensing of fluids. We show that by introducing a chirp in the hole size, the MOF can be a structure with decoupled cores, forming a Mach-Zehnder interferometer in which the analyte directly modulates the device transmittance by its differential influence on the effective refractive index of each core mode. We show that by filling all fiber holes with analyte, the sensing structure achieves high sensitivity (transmittance changes of 300 per RIU at 1.42) and has the potential for use over a wide range of analyte refractive index.