Nodular polypropylene from reactor granule technology for the production of a stiff and ductile material.

No abstract

Understanding the complex crystallization behavior of isotactic polypropylene (iPP) in conditions comparable to those found in polymer processing, where the polymer melt experiences a combination of high shear rates and elevated pressures, is key for modeling and therefore predicting the final structure and properties of iPP products. Coupling a unique experimental setup, capable to apply wall shear rates similar to those experienced during processing and carefully control the pressure before and after flow is imposed, with in situ X-ray scattering and diffraction techniques (SAXS and WAXD) at fast acquisition rates (up to 30 Hz), a well-defined series of short-term flow experiments are carried out using 16 different combinations of wall shear rates (ranging from 110 to 440 s–1) and pressures (100–400 bar). A complete overview on the kinetics of structure development during and after flow is presented. Information about shish formation and growth of α-phase parents lamellae from the shish backbones is extracted from SAXS; the overall apparent crystallinity evolution, amounts of different phases (α, β, and γ), and morphologies developing in the shear layer (parent and daughter lamellae both in α and γ phase) are fully quantified from the analysis of WAXD data. Both flow rate and pressure were found to have a significant influence on the nucleation and the growth process of oriented and isotropic structures. Flow affects shish formation and the growth of α-parents; pressure acts on relaxation times, enhancing the effect of flow, and (mainly) on the growth rate of γ-phase. The remarkably high amount of γ-lamellae found in the oriented layer strongly indicates the nucleation of γ directly from the shish backbone. All the observations were conceptually in agreement with the flow-induced crystallization model framework developed in our group and represent a unique and valuable data set that will be used to further validate and implement our numerical modeling, filling the gap for quantitatively modeling crystallization during complicated processing operations like injection molding.

published version features the final layout of the paper including the volume, issue and page numbers. Link to publication General rightsCopyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights.• Users may download and print one copy of any publication from the public portal for the purpose of private study or research. • You may not further distribute the material or use it for any profit-making activity or commercial gain • You may freely distribute the URL identifying the publication in the public portal.If the publication is distributed under the terms of Article 25fa of the Dutch Copyright Act, indicated by the "Taverne" license above, please follow below link for the End User

No abstract

We report on the effect of an aliphatic oxalamide based nucleating agent (OXA3,6) on the melt and crystallization behavior of isotactic polypropylene (iPP) under defined shear conditions. Through polarized optical microscopy, we demonstrate that OXA3,6 self-assembles from the iPP melt into rhombic crystals whereas their size and distribution proved highly dependent on the employed cooling rates. The presence of 0.5 wt % of OXA3,6 in iPP results in a significant suppression in iPP melt viscosity, which could not be explained via molecular modeling. A possible cause for the drop in viscosity in the presence of OXA3,6 is attributed to the interaction (absorption) of high molecular weight iPP chains with the nucleating agent, thereby suppressing their contribution to the viscoelastic response of the melt. This proposed mechanism for the suppression in melt viscosity appears similar to that encountered by the homogeneous distribution of nanoparticles such as CNTs, graphene, and silica. Shear experiments, performed using a slit flow device combined with small-angle X-ray diffraction measurements, indicate that crystallization is significantly enhanced in the presence of OXA3,6 at relatively low shear rates despite its lowered sensitivity to shear. This enhancement in crystallization is attributed to the shear alignment of the rhombic OXA3,6 crystals that provide surface for iPP kebab growth upon cooling. Overall, the suppression in melt viscosity in combination with enhanced nucleation efficiency at low as well as high shear rates makes this self-assembling oxalamide based nucleating agent a promising candidate for fast processing.

Structure formation during flow, a common phenomenon driving polymer processing, can have a major effect on the rheological behavior of a polymer melt. This can cause large increases of the pressure and thus large changes in thermodynamical properties which, in turn, will strongly influence the structure formation. Consequently, a complex, mutual, self-influencing process, occurring at rather short times, arises. This process is investigated with combined in situ small-angle X-ray scattering and wide-angle X-ray diffraction at high acquisition frequency (30 Hz) in a piston driven slit flow device using linear low density polyethylene as a model material. A decrease of crystallinity is observed immediately after flow and related to an unusual melting of part of the oriented crystals. The experimental observation is explained in terms of pressure dependency of the undercooling. The undercooling first increases during flow because of the pressure rise and then drops when pressure relaxes to equilibrium values; as a consequence, the critical stable lamellar thickness is not constant in time, although the experiments are conducted in isothermal conditions. A mechanism is proposed and validated using a structural model to fit SAXS data: the increase of undercooling during flow promotes nucleation of gradually thinner lamellae on the pre-existing kebab nucleated from shish cores that relax back to the melt state after depressurization. Our results show that in modeling real-life processes involving combination of flow and high pressures, like injection molding, the effect of pressure on the shear layer formation cannot be neglected.

This detailed study reveals the relation between structural evolution and the mechanical response of α-, β-and γ-iPP. Uni-axial compression experiments, combined with in situ WAXD measurements, allowed for the identification of the evolution phenomena in terms of phase composition. Tensile experiments in combination with SAXS revealed orientation and voiding phenomena, as well as structural evolution in the thickness of the lamellae and amorphous layers. On the level of the crystallographic unit cell, the WAXD experiments provided insight into the early stages of deformation. Moreover, transitions in the crystal phases taking place in the larger deformation range and the orientation of crystal planes were monitored. At all stretching temperatures, the crystallinity decreases upon deformation, and depending on the temperature, different new structures are formed. Stretching at low temperatures leads to crystal destruction and the formation of the oriented mesophase, independent of the initial polymorph. At high temperatures, above Tα c , all polymorphs transform into oriented α-iPP. Small quantities of the initial structures remain present in the material. The compression experiments, where localization phenomena are excluded, show that these transformations take place at similar strains for all polymorphs. For the post yield response, the strain hardening modulus is decisive for the mechanical behavior, as well as for the orientation of lamellae and the evolution of void fraction and dimensions. β-iPP shows by far the most intense voiding in the entire experimental temperature range. The macroscopic localization behavior and strain at which the transition from disk-like void shapes, oriented with the normal in tensile direction, into fibrillar structures takes place is directly correlated with the strain hardening modulus.