Improving the long-term stability of perovskite solar cells is critical to the deployment of this technology. Despite the great emphasis laid on stability-related investigations, publications lack consistency in experimental procedures and parameters reported. It is therefore challenging to reproduce and compare results and thereby develop a deep understanding of degradation mechanisms. Here, we report a consensus between researchers in the field on procedures for testing perovskite solar cell stability, which are based on the International Summit on Organic Photovoltaic Stability (ISOS) protocols. We propose additional procedures to account for properties specific to PSCs such as ion redistribution under electric fields, reversible degradation and to distinguish ambient-induced degradation from other stress factors. These protocols are not intended as a replacement of the existing qualification standards, but rather they aim to unify the stability assessment and to understand failure modes. Finally, we identify key procedural information which we suggest reporting in publications to improve reproducibility and enable large data set analysis.

Polymeric semiconductors are materials where unique optical and electronic properties often originate from a tailored chemical structure. This allows for synthesizing conjugated macromolecules with ad hoc functionalities for organic electronics. In photovoltaics, donoracceptor co-polymers, with moieties of different electron affinity alternating on the chain, have attracted considerable interest. The low bandgap offers optimal light-harvesting characteristics and has inspired work towards record power conversion efficiencies. Here we show for the first time how the chemical structure of donor and acceptor moieties controls the photogeneration of polaron pairs. We show that co-polymers with strong acceptors show large yields of polaron pair formation up to 24% of the initial photoexcitations as compared with a homopolymer (η = 8%). π-conjugated spacers, separating the donor and acceptor centre of masses, have the beneficial role of increasing the recombination time. The results provide useful input into the understanding of polaron pair photogeneration in low-bandgap co-polymers for photovoltaics.

Impedance spectroscopy has been widely applied over the last decades to study electrochemical systems and solid-state devices. However, performing impedance spectroscopy on emerging photovoltaics presents new challenges related to the unusual material properties and complex device architectures. This review provides an introduction to impedance spectroscopy for researchers in photovoltaics and closely related fields. The review begins with a list of practical guidelines for performing measurements and analyzing data. After this, the mathematical basics are reviewed, and an introduction to circuit elements is given. This is followed by tips for collecting reliable data and reducing artifacts in the frequency spectra. The review then surveys common approaches in the field for analyzing data, including performing equivalent circuit modeling, analysis of capacitance-frequency spectra, and carrier mobility measurements. The underlying assumptions of each analysis approach, as well as the advantages, limitations, and potential pitfalls are discussed.

General rightsThis document is made available in accordance with publisher policies. Please cite only the published version using the reference above. Full terms of use are available: http://www.bristol.ac.uk/pure/about/ebr-terms AbstractIn a quest to fabricate novel solar energy materials, the high quantum efficiency and long charge separated states of photosynthetic pigment-proteins are being exploited through their direct incorporation in bioelectronic devices. In this work, photocurrent generation by bacterial reaction center-light harvesting 1 (RC-LH1) complexes self-assembled on a nanostructured silver substrate yielded a peak photocurrent of 166 µA cm -2 under 1 sun illumination, and a maximum of over 400 µA cm -2 under 4 suns, the highest reported to date.A 2.5-fold plasmonic enhancement of light absorption per RC-LH1 complex was measured on the rough silver substrate. This plasmonic interaction was assessed using confocal fluorescence microscopy, revealing an increase of fluorescence yield and radiative rate of the RC-LH1 complexes. Nano-structuring of the silver substrate also enhanced the stability of the protein under continuous illumination by almost an order of magnitude relative to a nonstructured bulk silver control. Due to its ease of construction, increased protein loading capacity, stability and more efficient use of light, this hybrid material is an excellent candidate for further development of plasmon enhanced biosensors and bio-photovoltaic devices.3

The influence of the hole transport layer on device stability in polymer:fullerene bulk‐heterojunction solar cells is reported. Three different hole transport layers varying in composition, dispersion solvent, electrical conductivity, and work function were used in these studies. Two water‐based hole transport layers, poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) and polyaniline:poly(styrene sulfonate), and one isopropyl alcohol‐based polyaniline:poly(styrene sulfonate) transport layer were investigated. Solar cells with the different hole transport layers were fabricated and degraded under illumination. Current–voltage, capacitance–voltage, and capacitance–frequency data were collected at light intensities of 16, 30, 48, 80, and 100 mW cm−2 over a period of 7 h. Device performance and stability were compared between nonencapsulated and encapsulated samples to gain understanding about degradation effects related to oxygen and water as well as degradation mechanisms related to the intrinsic instability of the solar cell materials and interfaces. It is demonstrated that the properties of the hole transport layer can have a significant impact on the stability of organic solar cells.

Molecular doping of conjugated polymers represents an important strategy for improving organic electronic devices. However, the widely reported low efficiency of doping remains a crucial limitation to obtain high performance. Here we investigate how charge transfer between dopant and donor-acceptor copolymers is affected by the spatial arrangement of the dopant molecule with respect to the copolymer repeat unit. We p-dope a donor-acceptor copolymer and probe its charge-sensitive molecular vibrations in films by infrared spectroscopy. We find that, compared with a related homopolymer, a four times higher dopant/ polymer molar ratio is needed to observe signatures of charges. By DFT methods, we simulate the vibrational spectra, moving the dopant along the copolymer backbone and finding that efficient charge transfer occurs only when the dopant is close to the donor moiety. Our results show that the donor-acceptor structure poses an obstacle to efficient doping, with the acceptor moiety being inactive for p-type doping.

The addition of small amounts of dodecylamine-capped Au nanoparticles into the active layer of organic bulk heterojunction solar cells consisting of poly(3-octylthiophene) (P3OT) and C(60) was recently suggested to have a positive impact on device performance due to improved electron transport. This issue was systematically further investigated in the present work. Different strategies to incorporate colloidally prepared Au nanoparticles with a narrow size distribution into organic solar cells with the more common donor/acceptor system consisting of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C(61)-butyric acid methyl ester (PCBM) were pursued. Au nanoparticles were prepared with either P3HT or dodecylamine as ligands. Additionally, efforts were undertaken to incorporate nearly ligand-free Au nanoparticles into the system. Therefore, a procedure was successfully developed to remove the dodecylamine ligand shell by a postpreparative ligand exchange with pyridine, a much smaller molecule that can later partly be removed from solid films by annealing. However, for all types of nanoparticles studied here, the performance of the P3HT/PCBM solar cells was found to decrease with the Au particles as an additive to the active layer, meaning that adding Au nanoparticles is not a suitable strategy in the case of the P3HT/PCBM system. Possible reasons are discussed on the basis of detailed investigations of the structure, photophysics and charge transport in the system.

functionality such as solution processing, have been the motivation driving these technologies. Additionally, compared to more conventional photovoltaics such as silicon solar cells, the device operation principles of many of these thin fi lm photovoltaic technologies are dependent on complex physical mechanisms, such as excitonic processes, photoinduced charge separation, functional material interfaces.Whereas initial research efforts were focused on understanding the underlying device physics and improvements in power conversion effi ciency, with increasing maturity of these photovoltaic technologies, growing efforts are now being invested into the understanding of underlying degradation mechanisms and the improvement of device stability. In addition to effi ciency, increased device lifetimes are fundamental requirements for transforming these technologies into an economic viability. In early studies, many stability investigations with various stress conditions were conducted in order to gain a better understanding of the degradation mechanisms. Currently, however, a consolidation towards some common stress scenarios for stability has been pursued in order to enable a better comparability between results of different research labs worldwide. A particularly well organized large scale effort was conducted within the framework of the International Summit on Organic Solar Cell Stability (ISOS), leading to the so-called ISOS-protocols. Nowadays, During the last few decades, and in some cases only the last few years, novel thin-fi lm photovoltaic (PV) technologies such as dye-sensitized solar cells (DSSC), organic solar cells (OPV), and, more recently, perovskite-based solar cells (PSC) have been growing in maturity with respect to device performance and device stability. Together with new material systems, novel device architectures have also been introduced. Both parameters will have an effect on the overall device stability. In order to improve the understanding of degradation effects and how they can be prevented, stress testing under different conditions is commonly applied. By careful combination of stress factors and thorough analysis of photovoltaic parameter decaying curves, an understanding of the underlying degradation pathways can be gained. With the help of standardized and accelerated stress tests, as described in the ISOS-protocols, statements concerning application lifetimes can fi nally be made and compared among different labs. Once a photovoltaic technology has proven long lasting durability, the ultimate barrier for entering the commercial market are the IEC tests, taking a deeper look on overall safety and reliability, not only on durability. Here, the most prominent stress tests are reviewed, discussed and extended with respect to learning the most about photovoltaic device stability.