Previous work in our laboratory showed the potential of using a human recombinant elastin-like polypeptide (ELP) as a thromboresistant coating. In this work we investigate the use of three particular ELPs (ELP1, ELP2 and ELP4), that differ by molecular weight and number of repeating hydrophobic and cross-linking domains, as coatings to improve blood-contacting properties. All three ELPs were passively adsorbed on Mylar surfaces. Differences in water contact angle and surface concentration were found among the three ELP coatings, with the shortest polypeptide, ELP1, being the most hydrophilic and abundant on the surface (55°, 0.76 μg/cm(2)), followed by ELP2 (55°, 0.35 μg/cm(2)) and ELP4, the longest of the three (66°, 0.25 μg/cm(2)), respectively. The blood interactions of the ELP coatings were investigated by measuring fibrinogen adsorption and platelet adhesion in whole blood under laminar flow in a cone and plate viscometer configuration. In general, platelet adhesion to the ELP-coated surfaces was found to correlate with fibrinogen adsorption. Decreases in fibrinogen accretion and platelet adhesion were observed for ELP-coated compared to uncoated surfaces. The magnitude of the decreases was found to depend on the ELP sequence length, with ELP4 exhibiting the lowest levels of fibrinogen adsorption and platelet adhesion at 43 ± 24 ng/cm(2) and 113 ± 77 platelets/mm(2), respectively.

Recombinantly-engineered elastin-like polypeptides (ELPs) possess many of the favourable attributes of the native elastin protein, making them an attractive option for designing biomaterials for tissue-engineering applications. The focus of this study was to synthesize and characterise the bulk material properties of two ELP sequences, ELP2 and ELP4, cross-linked with lysine diisocyanate (LDI). The two distinct ELPs consist of repeating hydrophobic and hydrophilic cross-linking domains in a block co-polymer structure, however, differ by the number of respective domains. Depending on the conditions sets for the cross-linking reactions, two different ELP-based materials were synthesized: a gel-like relatively non-porous material and a porous foam-like material, from both ELP sequences. The physical material properties were characterised by scanning electron microscopy, compression testing, differential calorimetry analysis and swelling analysis. The bulk material properties were found to vary depending on the ELP sequence investigated. ELP gels were also found to have a more dense solidified morphology, lower compressive moduli, higher melting temperature and greater swelling capacity than the porous ELP foams. These novel cross-linked bio-elastomeric materials show promising properties for soft tissue replacement, particularly in load-bearing applications.

In this work, we expand on our understanding of the thrombogenicity of coatings prepared with three different recombinant elastin-like polypeptides (ELPs). The bulk platelet response of the ELP coatings was characterized following whole blood contact under physiological shear flow (300 s(-1) ) using flow cytometry. Prolonged exposure to shear flow (1-h) indicated that materials coated with the longer ELP coatings (ELP2 and ELP4) had less bulk platelet activation and microparticle formation than materials coated with the shorter ELP1. Quartz crystal microbalance with dissipation (QCM-D) was used to monitor the binding of the platelet membrane receptor GPIIb/IIIa to ELP-adsorbed fibrinogen (Fg) surfaces. Compared to the shorter ELPs, a lower amount of Fg adsorbed to the ELP4 coated material and ELP4 appeared to form a softer, more structurally flexible coating layer. When Fg was adsorbed to the ELP coated surface it demonstrated an altered binding for GPIIb/IIIa that was inhibited in the presence of an AGDV-containing peptide but not an RGD-containing peptide. Conversely, on the shorter ELP coatings, binding of GPIIb/IIIa to an adsorbed Fg layer was partially inhibited in the presence of an RGD-containing peptide. These results indicate that both the quantity and conformational state of Fg varies when adsorbed to surfaces coated with ELPs of varying sequence length, which may be mediating their platelet response. Collectively, the findings reinforce the applicability of the ELPs as potential thromboresistant coatings, especially with the use of the longer polypeptide-ELP4.

No abstract

The surface properties of a family of elastin-like polypeptides (ELPs), differing in molecular weight and sequence length, were investigated to understand how the nature of the polypeptide film might contribute to their thrombogenic profile. Physical adsorption of the ELPs onto Mylar increased surface wettability as the sequence length decreased while X-ray spectroscopy analysis showed an increasing amide content with sequence length. Chemical force microscopy analysis revealed that the ELP-coated surfaces displayed purely hydrophilic adhesion forces that increased as the ELP sequence length decreased. Adsorption isotherms performed using the quartz crystal microbalance with dissipation, showed that the surface coverage increased with ELP sequence length. The longer polypeptides (ELP2 and ELP4) also displayed higher specific dissipation values indicating that they established films with greater structural flexibility and associated water content than the shorter polypeptide, ELP1. Additionally, the stability of the ELP coating was lower with the shorter polypeptides. This study highlights the different surface properties of the ELP coatings as well as the dynamic nature of the ELP adsorbed layer wherein the conformational state may be an important factor contributing to their blood response.