Objective: To evaluate the effect of cavity dimensions on the amount of microleakage in two different types of bulk-fill composite resins. Material and Methods: Forty class II cavities were prepared in the mesial and distal surfaces of human molars without any carious lesions. The samples were divided into 4 groups (n=10): Group 1: cavities with 3 mm of buccolingual width (known as the smaller cavity), filled with Tetric N-Ceram Bulk Fill composite resin; Group 2: cavities with 6 mm of buccolingual width (larger cavity), filled with Tetric N-Ceram Bulk Fill composite resin; Group 3: cavities with 3 mm of buccolingual width, filled with X-Tra Base composite resin; and Group 4: cavities with 6 mm of buccolingual width, filled with X-Tra Base composite. After the specimens were thermocycled for 500 cycles at 5/55°C, they were immersed in 1% methylene blue for 24 hours, and then cut into sections mesiodistally in the longitudinal axis of each tooth. Then, the samples were scored regarding the amount of dye penetration in two occlusal and gingival areas under a stereomicroscope (x32). Data was submitted to Kruskal-Wallis and Mann-Whitney tests. Results: The highest degrees of microleakage in larger cavities filled with X-Tra Base among the four groups. There was a significant statistic difference (p=0.012) between large and small cavities filled with X-Tra Base (Groups 3 and 4); however, there was no significant difference between the two cavity sizes of Tetric N-Ceram Bulk-filled groups. Conclusion: Microleakage of composite resins depends on the dimension of the cavity and the type of composite resin used.
To evaluate the effect of a resin coating material on the microleakage of Class V composite resin restorations with and without post-operative bleaching. Material and Methods: Eighty class V cavities (3×3×1.5 mm) were prepared and filled with Z250 XT composite resin in the buccal and lingual surfaces of 40 sound human molars. Then the samples were randomly divided into 4 groups (n=20) and treated as follows: Group A: applying a resin coating (G-Coat Plus) on the restoration, then bleaching with 40% hydrogen peroxide; Group B: Post-Operative bleaching without prior use of resin coating; Group C: applying resin coating agent, and no further bleaching; and Group D: no resin coating, no bleaching. The specimens were thermocycled and immersed in 1% methylene blue for 24 hours, then cut into sections bucco-lingually. The samples were scored regarding the amount of dye penetration under a stereomicroscope (x20). Data were analyzed with Chi-squared and Fisher exact tests (p<0.05). Results: The maximum gingival and occlusal microleakage was detected in group B, while the minimum was seen in group C. In all the groups, microleakage at gingival margins was higher than occlusal margins (p<0.001). Conclusion: Application of a resin coating is an effective method in reducing microleakage of the restorations before and after bleaching.
Introduction. The use of technology in bulk-fill composites (BCs) has reduced the stresses caused by polymerization shrinkage, debonding, microleakage, or posttreatment sensitivity in them. This study was conducted to determine whether bleaching affects the microleakage of class II restoration with bulk-fill material. Materials and Methods. This laboratory study was performed on 40 normal human premolars in 4 groups (n = 20). Class II cavities were prepared in mesial and distal surfaces of the teeth with dimensions of 2 × 2 × 4 mm. Then, based on the bleaching process by 20% carbamide peroxide gel and using two types of composites, the restored cavities were randomly divided into 4 groups: (1) CC without bleaching (CC group), (2) BC without bleaching (BC group), (3) CC with bleaching (CCB group), and (4) BC with bleaching (BCB group). Then, the samples were thermocycled for 1000 cycles at a temperature range of 5–55°C, and they were immersed in 0.6% alkaline fuchsine in order to penetrate into the pigment for 24 h. After cutting, the samples were placed under a stereomicroscope (40%) to determine microleakage. The data were analyzed using one-way analysis of variance (ANOVA), and a p value <0.05 was considered as statistically significant. Results. Microleakage was determined in the CC group 0.97 ± 0.42 , BC group 1.08 ± 0.54 , CCB group 1.19 ± 0.37 , and BCB group 0.30 ± 0.47 . There were also no significant differences in the mean microleakage between the groups. No cases with zero microleakage (no microleakage) and grade 3 of microleakage (pigment penetration into the axial wall) were observed in the samples. Also, a two-by-two comparison of significant differences between CC and BC groups p = 0.89 , CC and CCB groups p = 0.45 , CC and BCB groups p = 0.11 , BC and CCB groups p = 0.87 , BC and BCB groups p = 0.41 , and CCB and BCB groups p = 0.86 showed that the difference was not statistically significant. Conclusion. Results showed no difference between microleakage of BC and CC with and without bleaching, and bleaching had the same effect on microleakage of these two types of composites.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.