ith the growing importance and falling prices of renewable electricity, the issue of electricity storage to deal with the intermittent nature of renewable energy sources is becoming urgent. Storing renewable electricity in chemical bonds ('electrofuels') is particularly attractive, as it allows for high-energy-density storage and potentially high flexibility. While hydrogen is the most likely and realistic candidate for electricity storage in electrofuels, research on the electrochemical conversion of carbon dioxide and water into carbon-based fuels has intrigued electrochemists for decades, and is currently undergoing a notable renaissance [1][2][3][4] . In contrast to hydrogen production by water electrolysis, carbon dioxide electrolysis is still far from a mature technology. Significant hurdles regarding energy efficiency, reaction selectivity and overall conversion rate need to be overcome if electrochemical carbon dioxide reduction is to become a viable option for storing renewable electricity.Many electrocatalysts have been reported for the production of different compounds from the electrocatalytic carbon dioxide reduction reaction (CO 2 RR). Table 1 gives an overview of some of the most active and selective metal or metal-derived electrocatalysts towards specific products in aqueous media. The two-electron transfer products, CO and HCOOH, can be produced with low overpotential and high Faradaic efficiency on suitable electrocatalysts, but substantially higher overpotentials and lower selectivities are observed for multi-electron transfer products such as methane, ethylene and alcohols 2 . For a recent discussion about the economic perspectives of CO 2 RR, the reader is referred to a previous analysis 5 .The aim of this Review is not to be exhaustive, but rather to selectively (and subjectively) discuss some recent advances and pertinent challenges in this field, focusing on themes that have recently witnessed important progress 2,3,6,7 . An overview of some of the themes covered in this Review is shown in Fig. 1. We also discuss two important methodologies used to increase fundamental understanding of CO 2 RR: in situ spectroscopic techniques and computational techniques.

Carbon dioxide and carbon monoxide can be electrochemically reduced to useful products such as ethylene and ethanol on copper electrocatalysts. The process is yet to be optimized and the exact mechanism and the corresponding reaction intermediates are under debate or unknown. In particular, it has been hypothesized that the C-C bond formation proceeds via CO dimerization and further hydrogenation. Although computational support for this hypothesis exists, direct experimental evidence has been elusive. In this work, we detect a hydrogenated dimer intermediate (OCCOH) using Fourier transform infrared spectroscopy at low overpotentials in LiOH solutions. Density functional theory calculations support our assignment of the observed vibrational bands. The formation of this intermediate is structure sensitive, as it is observed only during CO reduction on Cu(100) and not on Cu(111), in agreement with previous experimental and computational observations.

The complexity of the electrocatalytic reduction of CO to CH4 and C2H4 on copper electrodes prevents a straightforward elucidation of the reaction mechanism and the design of new and better catalysts. Although structural and electrolyte effects have been separately studied, there are no reports on structure-sensitive cation effects on the catalyst’s selectivity over a wide potential range. Therefore, we investigated CO reduction on Cu(100), Cu(111), and Cu(polycrystalline) electrodes in 0.1 M alkaline hydroxide electrolytes (LiOH, NaOH, KOH, RbOH, CsOH) between 0 and −1.5 V vs RHE. We used online electrochemical mass spectrometry and high-performance liquid chromatography to determine the product distribution as a function of electrode structure, cation size, and applied potential. First, cation effects are potential dependent, as larger cations increase the selectivity of all electrodes toward ethylene at E > −0.45 V vs RHE, but methane is favored at more negative potentials. Second, cation effects are structure-sensitive, as the onset potential for C2H4 formation depends on the electrode structure and cation size, whereas that for CH4 does not. Fourier Transform infrared spectroscopy (FTIR) and density functional theory help to understand how cations favor ethylene over methane at low overpotentials on Cu(100). The rate-determining step to methane and ethylene formation is CO hydrogenation, which is considerably easier in the presence of alkaline cations for a CO dimer compared to a CO monomer. For Li+ and Na+, the stabilization is such that hydrogenated dimers are observable with FTIR at low overpotentials. Thus, potential-dependent, structure-sensitive cation effects help steer the selectivity toward specific products.

No abstract

Carbon dioxide and carbon monoxide can be electrochemically reduced to useful products such as ethylene and ethanol on copper electrocatalysts. The process is yet to be optimized and the exact mechanism and the corresponding reaction intermediates are under debate or unknown. In particular, it has been hypothesized that the C−C bond formation proceeds via CO dimerization and further hydrogenation. Although computational support for this hypothesis exists, direct experimental evidence has been elusive. In this work, we detect a hydrogenated dimer intermediate (OCCOH) using Fourier transform infrared spectroscopy at low overpotentials in LiOH solutions. Density functional theory calculations support our assignment of the observed vibrational bands. The formation of this intermediate is structure sensitive, as it is observed only during CO reduction on Cu(100) and not on Cu(111), in agreement with previous experimental and computational observations.

Carbon dioxide (CO2) is currently considered as a waste material due to its negative impact on the environment. However, it is possible to create value from CO2 by capturing and utilizing it as a building block for commodity chemicals. Electrochemical conversion of CO2 has excellent potential for reducing greenhouse gas emissions and reaching the Paris agreement goal of zero net emissions by 2050. To date, Carbon Capture and Utilization (CCU) technologies (i.e. capture and conversion) have been studied independently. In this communication, we report a novel methodology based on the integration of CO2 capture and conversion by the direct utilization of a CO2 capture media as electrolyte for electrochemical conversion of CO2. This has a high potential for reducing capital and operational cost when compared to traditional methodologies (i.e. capture, desorption and then utilization). A novel mixture of chemical and physical absorption solvents allowed for the captured CO2 to be converted to formic acid with faradaic efficiencies up to 50 % and with carbon conversion of ca. 30 %. By increasing the temperature in the electrochemical reactor from 20 °C to 75 °C, the productivity towards formic acid increased by a factor of 10, reaching up to 0.7 mmol•m-2 •s-1. The direct conversion of captured CO2 was also demonstrated for carbon monoxide formation with faradaic efficiencies up 45 %.

In industrial electrochemical processes it is of paramount importance to achieve efficient, selective processes to produce valuable chemicals while minimizing the energy input. Although the electrochemical reduction of CO2 has received a lot of attention in the last decades, an economically feasible process has not yet been developed. Typically, the electrochemical reduction of CO2 is paired to water oxidation, forming oxygen, but an alternative strategy would be coupling the CO2 reduction reaction to an oxidation in which a higher-value product is co-produced, significantly improving the economic feasibility for CO2 reduction as a whole. Importantly, both reactions need to be chosen wisely, to ensure their compatibility and to minimize the voltage requirements for the redox system. In this study, as an example of this approach, we demonstrate such a match-the electroreduction of CO2 to CO, paired with the electrooxidation of 1,2-propanediol to lactic acid. Combining these reactions decreases energy consumption by ca. 35%, increases of product value of the system, and results in combined faradaic efficiencies of up to 160% when compared to the CO2 reduction reaction in which oxygen is formed in the anode.

Ruthenium polypyridyl complexes are good candidates for photoactivated chemotherapy (PACT) provided that they are stable in the dark but efficiently photosubstitute one of their ligands. Here the use of the natural amino acid l-proline as a protecting ligand for ruthenium-based PACT compounds is investigated in the series of complexes Λ-[Ru(bpy)2(l-prol)]PF6 ([1a]PF6; bpy = 2,2′-bipyridine and l-prol = l-proline), Λ-[Ru(bpy)(dmbpy)(l-prol)]PF6 ([2a]PF6 and [2b]PF6; dmbpy = 6,6′-dimethyl-2,2′-bipyridine), and Λ-[Ru(dmbpy)2(l-prol)]PF6 ([3a]PF6). The synthesis of the tris-heteroleptic complex bearing the dissymmetric proline ligand yielded only two of the four possible regioisomers, called [2a]PF6 and [2b]PF6. Both isomers were isolated and characterized by a combination of spectroscopy and density functional theory calculations. The photoreactivity of all four complexes [1a]PF6, [2a]PF6, [2b]PF6, and [3a]PF6 was studied in water (H2O) and acetonitrile (MeCN) using UV–vis spectroscopy, circular dichroism spectroscopy, mass spectrometry, and 1H NMR spectroscopy. In H2O, upon visible-light irradiation in the presence of oxygen, no photosubstitution took place, but the amine of complex [1a]PF6 was photooxidized to an imine. Contrary to expectations, enhancing the steric strain by the addition of two ([2b]PF6) or four ([3a]PF6) methyl substituents did not lead, in phosphate-buffered saline (PBS), to ligand photosubstitution. However, it prevented photoxidation, probably as a consequence of the electron-donating effect of the methyl substituents. In addition, whereas [2b]PF6 was photostable in PBS, [2a]PF6 quantitatively isomerized to [2b]PF6 upon light irradiation. In pure MeCN, [2a]PF6 and [3a]PF6 showed non-selective photosubstitution of both the l-proline and dmbpy ligands, whereas the non-strained complex [1a]PF6 was photostable. Finally, in H2O–MeCN mixtures, [3a]PF6 showed selective photosubstitution of l-proline, thus demonstrating the active role played by the solvent on the photoreactivity of this series of complexes. The role of the solvent polarity and coordination properties on the photochemical properties of polypyridyl complexes is discussed.