Studies were conducted on Pb-free solder interconnects after aging for up to 1,000 h at temperatures of up to 150°C and submitting to drop testing. Cracks were shown to propagate along interphase boundaries (bulk solder/Cu 6 Sn 5 , Cu 6 Sn 5 /Cu 3 Sn, Cu 3 Sn/Cu, and bulk solder/Ag 3 Sn) and along the bulk solder. Intergranular propagation in the solder was rarely observed, although cross sectioning showed evidence of that particular path. There is a transition in preferred crack propagation with aging time and temperature, from the intermetallic layer to the bulk solder. Sulfur was found in the fracture surfaces and may be a weakening agent in these solders.
Studies on the morphology and crystallography of austenite precipitated from ferrite were performed in an Fe-22.5 pct Cr-4.7 pct Ni-3 pct Mo-duplex stainless steel. Samples were solution treated at 1325°C (yielding a grain size of approximately 2 mm), water quenched, and then aged at temperatures ranging from 700 °C to 1100 °C for times ranging from 5000 to 30,000 seconds. The morphology of grain boundary precipitates depends on the grain boundary segment at which the precipitates are formed, and may be adequately described by the Dubé classification system. Orientation relationships (ORs) between austenite and the ferritic matrix were determined with electron backscattered diffraction (EBSD) analysis, employing graphic and algebraic methods. Grain boundary precipitates exhibited Kurdjumov-Sachs (K-S) or Nishyiama-Wassermann (N-W) ORs with at least one of the adjacent grains, and in some cases relationships intermediate between K-S and N-W appeared. In approximately 60 pct of the cases examined, grain boundary precipitates show K-S or N-W ORs with both grains forming a boundary, though with small deviations (up to 5 deg) from the exact relationships.
auxílio com o desenvolvimento do método algébrico para cálculo das relações de orientação.Aos técnicos e funcionários do departamento pelo auxílio prestado durante o trabalho.Aos colegas e amigos do departamento pelo apoio e amizade. Em particular, ao amigos Augusto Teruo Morita, pela ajuda na automação do procedimento algébrico para cálculo das relações de orientação, e Antonio Jose Ramirez-Londoño, pelas trocas de idéias e informações.
RESUMOAços inoxidáveis dúplex apresentam uma estrutura composta por ferrita e austenita.O fato de a austenita ser estável à temperatura ambiente possibilita que esses aços sejam usados no estudo da reação de formação da austenita a partir da ferrita, podendo os resultados ser aplicados a aços de baixa liga, em que a austenita se transforma em martensita no resfriamento brusco, e a outros sistemas com transformações entre fases cúbicas de corpo centrado (CCC) e cúbicas de face centrada (CFC). Foram realizados estudos em um aço inoxidável dúplex do tipo DIN W.Nr. 1.4462 (UNS 31803). As amostras foram solubilizadas no campo ferrítico a 1325°C e resfriadas em água. As amostras foram ainda tratadas isotermicame nte em temperaturas entre 700°C e 1100°C por tempos entre 5.000 e 30.000 segundos. Deste modo, a formação de austenita a partir da ferrita foi estudada em seu estágio inicial e em estágios avançados da reação, com relação aos seus aspectos morfológicos e cristalográficos. As morfologias encontradas apresentaram variações dependentes dos segmentos de contorno de grão em que as partículas se formam. As partículas nucleadas nos contornos de grão podem ser adequadamente descritas pela classificação morfológica de Dubé. Além disso, essas partículas apresentaram, em geral, relações de orientação do tipo Kurdjumov-Sachs e Nishyiama-Wassermann com pelo menos um dos dois grãos, podendo ser encontradas relações intermediárias entre essas duas. . Em alguns casos, as partículas mantêm relações de orientação com os dois grãos adjacentes, apresentando pequenos desvios das relações exatas relatadas na literatura. As partículas de austenita intragranulares apresentam desvios em relação à relações exatas maiores do que os encontrados nas partículas de contornos de grão. Em alguns casos, as partículas intragranulares aparentam não apresentar relações de orientação com a matriz ferrítica.
ABSTRACTDuplex Stainless Steels have a structure composed by ferrite and austenite. The fact that austenite, in these steels, is stable at low temperatures, allows the use of these steels in studies of austenite formation from ferrite, in such way that the results can be applied to low alloy steels, in which austenite transforms to martensite upon rapid cooling, and to other systems containing transformations between body-centred cubic (BCC) and face-centred cubic (FCC) phases. Studies were performed on a DIN W.Nr. 1.4462 (UNS 31803) duplex stainless steel. The samples were solution treated in the ferrite region at 1325°C and water cooled. Samples were then submitted to isothermal treatments at temperatures betw...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations –citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.