The handling of Acid Mine Water done at PT. Alamjaya Bara Pratama utilizes Cao and from prior research, fly ash is used as an adsorbent in neutralising Acid Mine Water. Hence the resarcher conducted the research to compare the effectiveness of Cao and fly ash in neutralising Acid Mine Water. The usage of CaO nd fly ash uses a laboratorium scale with 1000ml of Acid Mine Water, a CaO mass variation of 0,4, 0,5 and 0,6 gram whereas with a fly ash mass variation of 50, 55 and 60 gram and a stirring speed of 50 and 100 rpm. Results shows that the addition of CaO and fly ash and stirring speed increases the pH and reduces the content of Fe and Mn. The adsorbtion of the metals Fe and Mn by CaO and coal fly ash can occurs as most CaO contains the mineral compund Epistilbite (CaAl2Si6O16.5H2O), before conducting the experiment it shows that most of the fly ash contains the mineral compund Quartz (SiO2) and mullite (Al6Si2O13). Silica and Alumina has a polar side with an active hydroxyl group (-OH) which acts in the adsorbtion process between heavy metals and adsorbents in a solution containing water.
Non-destructive testing(NDT) adalah pengujian material untuk menentukan kualitas dan integritas material atau elemen struktur tanpa memengaruhi kemampuan untuk menjalannya fungsinya. NDT itu sendiri memiliki beberapa metode pengujian, yaitu radiograph testing, eddy current testing, thermal testing, penetrant testing, ultrasonic testing, dan visual testing. Metode eddy curent biasanya digunakan untuk melihat crack maupun mengetahui perbedaan suatu material melalui nilai konduktivitasnya. Pada penelitian ini dimaksudkan untuk menanalisis dari teori yang ada dengan yang terjadi dilapangan, dengan menambahkan variasi ketebalan pada Aluminium clad sheet 2024. Cladding test sangat umum dilakukan di industri aviasi untuk menghindari, mengetahui lebih awal dan menanggulangi kecelakaan yang diakibatkan korosi karena cladding sudah hilang.
Perkembangan dunia teknologi telah mempengaruhi banyak aspek dalam kehidupan manusia, berbagai alat ataupun sistem telah dibuat untuk mempermudah kehidupan. Hal itu terlihat dari banyaknya barang elektronik yang diproduksi dan digunakan setiap harinya. Manusia sudah mempunyai ketergantungan yang tinggi terhadap barang-barang elektronik tersebut. Masa pakai dari barang elektronik tidak dapat bertahan lama dan munculnya produk dengan generasi baru membuat barang tersebut terlihat cepat usang dan tertinggal. Hal tersebut mendorong konsumen untuk mengganti barang elektroniknya dengan yang baru dalam kurun waktu yang lebih cepat. Akibatnya, terjadi penumpukan limbah elektronik (e-waste) yang tidak dapat dihindari lagi. Tujuan penelitian ini untuk menganalisis dan mencari waktu dengan hasil recovery emas tertinggi pada leaching emas (Au) pada limbah prosesor komputer menggunakan larutan organik Tiourea. Adapun metode yang digunakan pada penelitian ini adalah leaching atau pelindihan. Sampel dilakukan preparasi dengan melarutkan Tiourea, sehingga akan terbentuk endapan yang nantinya akan dipisahkan dan selanjutnya dilakukan pengujian Atomic Absorption Spectrophotometer (AAS). Variasi waktu leaching yang digunakan yaitu 1, 2, 3, 4 dan 5 jam. Recovery emas atau Au yang diperoleh sebesar 8,12% selama 1 jam leaching, 5,80% pada 2 jam leaching, 5,74% pada 3 jam leaching, 4,99% pada 4 jam leaching dan 4,36% pada 5 jam leaching. Dari parameter lamanya waktu pelarutan Tiourea terhadap recovery emas (Au) pada penelitian ini, menunjukkan pada 1 jam leaching menghasilkan nilai recovery yang paling tinggi sebesar 8,12% dengan kadar emas (Au) sebesar 1,0253 ppm. Kata kunci: leaching emas (Au), e-waste, recovery, Tiourea
Air-Tegal". Tujuan penelitian ini adalah untuk mengetahui pengaruh kuat arus terhadap kekuatan tariknya serta mengetahui cacat las yang diakibatkan oleh kuat arus yang tidak sesuai dengan welding procedure specification (WPS). Adapun metode pengujian adalah pertama mencari literatur-literatur penunjang, selanjutnya adalah pengumpulan data lapangan, kemudian menganalisis data. Adapun pengelasan dilakukan dengan metode SMAW dengan material berupa baja SM 400 B, dan elektroda E 7016 dengan diameter 3,2. Berdasarkan penelitian yang telah dilakukan diketahui bahwa semakin besar kuat arusnya maka akan semakin besar nilai kekuatan tariknya begitupun sebaliknya semakin kecil kuat arusnya maka semakin kecil pula nilai kekuatan tariknya. Selain itu, kuat arus harus sesuai dengan WPS. Jika arus pengelasan tidak sesuai WPS, maka akan terjadi cacat pengelasan. Arus pengelasan yang terlalu rendah akan menyebabkan cacat las berupa undercut, cacat las spatter, sedangkan arus pengelasan yang terlalu tinggi akan menyebabkan cacat las berupa porositas, incomplete peneration.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.