Since the first H-mode discharges in 2010, the duration of the H-mode state has been extended and a significantly wider operational window of plasma parameters has been attained. Using a second neutral beam (NB) source and improved tuning of equilibrium configuration with real-time plasma control, a stored energy of W tot ∼ 450 kJ has been achieved with a corresponding energy confinement time of τ E ∼ 163 ms. Recent discharges, produced in the fall of 2012, have reached plasma β N up to 2.9 and surpassed the n = 1 ideal no-wall stability limit computed for H-mode pressure profiles, which is one of the key threshold parameters defining advanced tokamak operation. Typical H-mode discharges were operated with a plasma current of 600 kA at a toroidal magnetic field B T = 2 T. L-H transitions were obtained with 0.8-3.0 MW of NB injection power in both single-and double-null configurations, with H-mode durations up to ∼15 s at 600 kA of plasma current. The measured power threshold as a function of lineaveraged density showed a roll-over with a minimum value of ∼0.8 MW at ne ∼ 2×10 19 m −3 . Several edge-localized mode (ELM) control techniques during H-mode were examined with successful results including resonant magnetic perturbation, supersonic molecular beam injection (SMBI), vertical jogging and electron cyclotron current drive injection into the pedestal region. We observed various ELM responses, i.e. suppression or mitigation, depending on the relative phase of in-vessel control coil currents. In particular, with the 90 • phase of the n = 1 RMP as the most resonant configuration, a complete suppression of type-I ELMs was demonstrated. In addition, fast vertical jogging of the plasma column was also observed to be effective in ELM pace-making. SMBI-mitigated ELMs, a state of mitigated ELMs, were sustained for a few tens of ELM periods. A simple cellular automata ('sand-pile') model predicted that shallow deposition near the pedestal foot induced small-sized high-frequency ELMs, leading to the mitigation of large ELMs. In addition to the ELM control experiments, various physics topics were explored focusing on ITER-relevant physics issues such as the alteration of toroidal rotation caused by both electron cyclotron resonance heating (ECRH) and externally applied 3D fields, and the observed rotation drop by ECRH in NB-heated plasmas was investigated in terms of either a reversal of the turbulence-driven residual stress due to the transition of ion temperature gradient to trapped electron mode turbulence or neoclassical toroidal viscosity (NTV) torque by the internal kink mode. The suppression of runaway electrons using massive gas injection of deuterium showed that runaway electrons were avoided only below 3 T in KSTAR. Operation in 2013 is expected to routinely exceed the n = 1 ideal MHD no-wall stability boundary in the long-pulse H-mode ( 10 s) by applying real-time shaping control, enabling n = 1 resistive wall mode active control studies. In addition, intensive works for ELM mitigation, ELM dynamics, toroidal ro...

No abstract

A plasma generator for a long pulse H(+)/D(+) ion source has been developed. The plasma generator was designed to produce 65 A H(+)/D(+) beams at an energy of 120 keV from an ion extraction area of 12 cm in width and 45 cm in length. Configuration of the plasma generator is a multi-cusp bucket type with SmCo permanent magnets. Dimension of a plasma chamber is 25 cm in width, 59 cm in length, and 32.5 cm in depth. The plasma generator was designed and fabricated at Japan Atomic Energy Agency. Source plasma generation and beam extraction tests for hydrogen coupling with an accelerator of the KSTAR ion source have been performed at the KSTAR neutral beam test stand under the agreement of Japan-Korea collaborative experiment. Spatial uniformity of the source plasma at the extraction region was measured using Langmuir probes and ±7% of the deviation from an averaged ion saturation current density was obtained. A long pulse test of the plasma generation up to 200 s with an arc discharge power of 70 kW has been successfully demonstrated. The arc discharge power satisfies the requirement of the beam production for the KSTAR NBI. A 70 keV, 41 A, 5 s hydrogen ion beam has been extracted with a high arc efficiency of 0.9 -1.1 A/kW at a beam extraction experiment. A deuteron yield of 77% was measured even at a low beam current density of 73 mA/cm(2).

No abstract

The first neutral beam (NB) injection system of the Korea Superconducting Tokamak Advanced Research (KSTAR) tokamak was partially completed in 2010 with only 1∕3 of its full design capability, and NB heating experiments were carried out during the 2010 KSTAR operation campaign. The ion source is composed of a JAEA bucket plasma generator and a KAERI large multi-aperture accelerator assembly, which is designed to deliver a 1.5 MW, NB power of deuterium at 95 keV. Before the beam injection experiments, discharge, and beam extraction characteristics of the ion source were investigated. The ion source has good beam optics in a broad range of beam perveance. The optimum perveance is 1.1-1.3 μP, and the minimum beam divergence angle measured by the Doppler shift spectroscopy is 0.8°. The ion species ratio is D(+):D(2)(+):D(3)(+) = 75:20:5 at beam current density of 85 mA/cm(2). The arc efficiency is more than 1.0 A∕kW. In the 2010 KSTAR campaign, a deuterium NB power of 0.7-1.5 MW was successfully injected into the KSTAR plasma with a beam energy of 70-90 keV. L-H transitions were observed within a wide range of beam powers relative to a threshold value. The edge pedestal formation in the T(i) and T(e) profiles was verified through CES and electron cyclotron emission diagnostics. In every deuterium NB injection, a burst of D-D neutrons was recorded, and increases in the ion temperature and plasma stored energy were found.

Ion optics of three accelerator geometries was studied in terms of an analytic linear optics analysis, a numerical simulation using the IGUN program, an optical multichannel measurement of Doppler-shifted H(alpha) lines, and a water-flow calorimetry on the beam absorbing target. In general, there was a reasonable agreement observed between the four analysis methods and thus the theoretical analyses can be utilized with confidence for design iteration.

No abstract

No abstract