One form of waterproof, breathable apparel is manufactured from polytetrafluoroethylene (PTFE) membrane laminated fabric, using a specific process to seal seams that have been sewn with traditional techniques. The sealing process involves applying waterproof tape to the seam by feeding the seam through two rollers while applying hot air (600°C). This study addressed the potential for exposure to particulate matter from this sealing process, by characterizing airborne particles in a facility that produces over 1,000 lightweight PTFE rain jackets per day. Aerosol concentrations throughout the facility were mapped, breathing zone concentrations were measured, and hoods used to ventilate the seam sealing operation were evaluated. The geometric mean (GM) particle number concentrations were substantially greater in the sewing and sealing areas (67,000 and 188,000 particles cm −3 ) compared to that measured in the office area (12,100 particles cm −3 ). Respirable mass concentrations were negligible throughout the facility (GM=0.002 mg m −3 in the sewing and sealing areas). The particles exiting the final discharge of the facility's ventilation system were dominated by nanoparticles (number median diameter = 25 nm; geometric standard deviation of 1.39). The breathing zone particle number concentrations of the workers who sealed the sewn seams were highly variable and significantly greater when sealing seams than when conducting other tasks (p<0.0001). The sealing workers' breathing zone concentrations ranged from 147,000 particles cm −3 to 798,000 particles cm −3 , and their seam responsibility significantly influenced their breathing zone concentrations (p=0.03). The finding that particle number concentrations were approximately equal outside the hood and inside the local exhaust duct indicated poor effectiveness of the canopy hoods used to ventilate sealing operations.

A four-stage personal diffusion battery (pDB) was designed and constructed to measure submicron particle size distributions. The pDB consisted of a screen-type diffusion battery, solenoid valve system, and electronic controller. A data inversion spreadsheet was created to solve for the number median diameter (NMD), geometric standard deviation (GSD), and particle number concentration of unimodal aerosols using stage number concentrations from the pDB combined with a handheld condensation particle counter (pDB+CPC). The inversion spreadsheet included particle entry losses, theoretical penetrations across screens, the detection efficiency of the CPC, and constraints so the spreadsheet solved to values within the pDB range. Size distribution parameters (NMD, GSD, and number concentration) measured with the pDB+CPC with inversion spreadsheet were within 25% of those measured with a scanning mobility particle sizer (SMPS) for 5 of 12 polydisperse combustion aerosols. For three tests conducted with propylene torch exhaust, the pDB+CPC with inversion spreadsheet successfully identified that the NMD was smaller than the constraint value of 16 nm. The ratio of the nanoparticle portion of the aerosol compared to the reference () was calculated to determine the ability of pDB+CPC with inversion spreadsheet to measure the nanoparticle portion of the aerosols. The ranged from 0.87 to 1.01 when the inversion solved and from 0.06 to 2.01 when the inversion solved to a constraint. The pDB combined with CPC has limited use as a personal monitor but combining the pDB with a different detector would allow for the pDB to be used as a personal monitor.

Previous research shows that police officers are at a higher risk for noise induced hearing loss (NIHL). Little data exists on the occupational tasks, outside of the firing range, that might lead to the increased risk of NIHL. The current study collected noise dosimetry from patrol officers in a smaller department and a larger department in southern Wisconsin, United States. The noise dosimeters simultaneously measured noise in three virtual dosimeters that had different thresholds, criterion levels, and exchange rates. The virtual dosimeters were set to: the Occupational Safety and Health Administration (OSHA) hearing conservation criteria (OSHA-HC), the OSHA permissible exposure level criteria (OSHA-PEL), and the American Conference of Governmental Industrial Hygienists (ACGIH). In addition to wearing a noise dosimeter during their respective work days, officers completed a log form documenting the type of task performed, the duration of that task, if the task involved the use of a siren, and officer characteristics that may have influenced their noise exposure, such as the type of dispatch radio unit worn. Analysis revealed that the normalized 8-hour time weighted averages (TWA) for all officers fell below the recommended OSHA and ACGIH exposure limits. The tasks involving the use of the siren had significantly higher levels than the tasks without (p = 0.005). The highest noise exposure levels were encountered when patrol officers were assisting other public safety agencies such as a fire department or emergency medical services (79 dBA). Canine officers had higher normalized 8-hr TWA noise exposure than regular patrol officers (p = 0.002). Officers with an evening work schedule had significantly higher noise exposure than the officers with a day or night work schedule (p = 0.023). There were no significant differences in exposure levels between the two departments (p = 0.22). Results suggest that this study population is unlikely to experience NIHL as established by the OSHA or ACGIH occupational exposure levels from the daily occupational tasks that were monitored.

One of the leading causes of noise-induced hearing loss is occupational noise exposure; however, little attention has been given to the exposure among amusement ride operators. According to the International Association of Amusement Parks and Attractions, 600,000 ride operators are employed in the U.S. The first objective of this descriptive study was to evaluate if ride operators were exposed to noise levels over 85 dB. The second objective was to classify the ride features that led to the highest noise levels. 136 rides were measured at 17 total amusement parks, county fairs, and festivals in southern Wisconsin and northern Illinois during summer 2015. A sound level meter recorded noise measurements as close in proximity to the ride operator as possible. Each ride was measured for two or three complete ride cycles, which included loading and operating the ride. The sound level meter was programmed to measure noise as recommended by the American Conference of Governmental Industrial Hygienists and with no threshold. 18% of rides measured had projected noise levels greater than American Conference of Governmental Industrial Hygienists recommendation of 85 dB. A repeated measures model was used to analyze the complete ride cycle decibel levels. The model found that traveling carnival rides had significantly higher levels compared to the stationary amusement park rides (p < 0.001), the rides operated near midway music had significantly higher levels than those without midway music (p < 0.001), and the type of ride was also significant. Tukey-Kramer multiple comparison test was used to determine differences in type of ride. According to the data, 18% of the amusement ride operators would be at risk for noise induced hearing loss and would require a hearing conservation program if the 8-hr time weighted averages were to follow the same trends as the complete ride cycle levels.

No abstract

The nanoparticle respiratory deposition (NRD) sampler is a personal sampler that combines a cyclone, impactor, and a nylon mesh diffusion stage to measure a worker’s exposure to nanoparticles. The concentration of titanium in the nylon mesh of the diffusion stage complicates the application of the NRD sampler for assessing exposures to titanium dioxide nanoparticles. This study evaluated commercially available nonwoven textiles for use as an alternative media in the diffusion stage of the NRD sampler. Three textiles were selected as containing little titanium from an initial screening of 11 textiles by field portable x-ray fluorescence (FPXRF). Further evaluation on these three textiles was conducted to determine the concentration of titanium and other metals by inductively coupled plasma – optical emission spectroscopy (ICP-OES), the number of layers required to achieve desired collection characteristics for use as the diffusion stage in the NRD sampler (i.e., the nanoparticulate matter, NPM, criterion), and the pressure drop associated with that number of layers. Only three (two composed of cotton fibers, C1 and C2; and one of viscose bamboo and cotton fibers, BC) of 11 textiles screened had titanium concentrations below the limit of detection the XRF device (0.15 μg/cm2). Multiple metals, including small amounts of titanium, were found in each of the three nonwoven textiles using ICP-OES. The number of 25-mm-diameter layers required to achieve the collection efficiency by size required for the NRD sampler was three for C1 (R2 = 0.95 with reference to the NPM criterion), two for C2 (R2 = 0.79), and three for BC (R2 = 0.87). All measured pressure drops were less than the theoretical and even the greatest pressure drop of 65.4 Pa indicated that a typical personal sampling pump could accommodate any of the three nonwoven textiles in the NRD sampler. The titanium concentration, collection efficiency, and measured pressure drops show there is a potential for nonwoven textiles to be used as the diffusion stage of the NRD sampler.

No abstract

This work strived to increase knowledge of assessing airborne nanoparticles in the workplace by characterizing nanoparticle concentrations in a workplace using directreading instruments, evaluating a DC2000CE diffusion charger, and the creation of a personal diffusion battery (pDB). Direct-reading instruments were used with aerosol mapping and task monitoring to evaluate airborne nanoparticle concentrations in an apparel company that produces waterproof jackets composed of polytetrafluoroethylene membrane laminated fabric. Jacket production required that sewn seams be sealed with waterproof tape applied with hot air (600°C). Particle number concentrations were greater in the sewing and sealing areas than the office area while respirable mass was negligible throughout the facility. The breathing zone particle number concentrations of the workers who sealed the sewn seams were highly variable and significantly greater when sealing seams than when conducting other tasks (p<0.0001). The effectiveness of the canopy hoods used to ventilate sealing operations was poor. These measurements support the idea that work places where hot processes are conducted may have substantially greater concentrations of airborne nanoparticles than background measurements even with control measures in place. Laboratory tests were conducted to evaluate a commercially available diffusion charger, the DC2000CE, that measures nanoparticle surface area concentration. The surface area concentrations of unimodal and multimodal polydispersed aerosols measured by the DC2000CE were less than the surface area concentrations measured by the reference instruments. The differences in results were attributed to a difference of measuring active versus geometric surface area concentration and the design of the DC2000CE. The maximum measurable active surface area concentration (2,500 mm 2 m-3) was found to be greater than the manufacturer stated maximum (1000 mm 2 m-3). Moving or vibrating a DC2000CE while taking measurements can cause v ABSTRACT This work strived to increase knowledge of assessing airborne nanoparticles in the workplace by characterizing nanoparticle concentrations in a workplace using directreading instruments, evaluating a DC2000CE diffusion charger, and the creation of a personal diffusion battery (pDB). Direct-reading instruments were used with aerosol mapping and task monitoring to evaluate airborne nanoparticle concentrations in an apparel company that produces waterproof jackets composed of polytetrafluoroethylene membrane laminated fabric. Jacket production required that sewn seams be sealed with waterproof tape applied with hot air (600°C). Particle number concentrations were greater in the sewing and sealing areas than the office area while respirable mass was negligible throughout the facility. The breathing zone particle number concentrations of the workers who sealed the sewn seams were highly variable and significantly greater when sealing seams than when conducting other tasks (p<0.0001). The effectiveness of the canopy hoo...