Efficient electrical doping of organic semiconductors is a necessary prerequisite for the fabrication of high performance organic electronic devices. In this work, we study p-type doping of poly(3-hexylthiophene) (P3HT) with 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F 4 TCNQ) spin-cast from two different solvents. Using electron diffraction, we find strong dopant-induced π−π-stacking for films from the solvent chloroform, but not from chlorobenzene. This image is confirmed and expanded by the analysis of vibrational features of P3HT and polaron absorptions using optical spectroscopy. Here, a red-shifted polaron absorption is found in doped films from chloroform, caused by a higher conjugation length of the polymer backbone. These differences result in a higher conductivity of films from chloroform. We use optical spectroscopy on the corresponding blend solutions to shed light on the origin of this effect and propose a model to explain why solutions of doped P3HT reveal more aggregation of charged molecules in chlorobenzene, whereas more order is finally observed in dried films from chloroform. Our study emphasizes the importance of solvent parameters exceeding the bare solubility of pure dopant and host material for the preparation of highly conductive doped films.
Hybrid solar cells based on organometal halide perovskite absorbers have recently emerged as promising class for cost- and energy-efficient photovoltaics. So far, unraveling the morphology of the different materials within the nanostructured absorber layer has not been accomplished. Here, we present the first visualization of the mesoporous absorber layer in a perovskite solar cell from analytical transmission electron microscopy studies. Material contrast is achieved by electron spectroscopic imaging. We found that infiltration of the hole transport material into the scaffold is low and inhomogeneous. Furthermore, our data suggest that the device performance is strongly affected by the morphology of the TiO2 scaffold with a fine grained structure being disadvantageous.
It is shown that the effect of substrate heating on the photo conversion effi ciency in vacuum-deposited small molecule organic solar cells is closely related to the improved free charge generation in ordered C 60 regions. The formation of these ordered regions strongly depends on the deposition sequence in the device and differs therefore between inverted and noninverted cells. Substrate-induced local fullerene ordering is found in small molecule:C 60 bulk heterojunctions (BHJs) deposited on pristine C 60 at elevated temperatures. This does not occur for BHJs deposited under identical conditions on pristine donor molecule layers, despite similar degrees of phase separation in both cases. These fi ndings point to a hitherto unidentifi ed advantage of inverted over noninverted solar cells that manifests itself in a higher charge separation effi ciency.
Transmission Electron Microscopy (TEM) can be utilized to understand the morphology of organic bulk heterojunction (BHJ) solar cells and thus aid in improving device performance. We have previously shown that phase separation and formation of crystallinity is to be expected during co‐evaporation of small molecule BHJ layers [1]. Using Electron Spectroscopic Imaging (ESI) [2] and electron diffraction, we found a significant influence of substrate and substrate temperature on the morphology of the photoactive layer during the fabrication of F 4 ZnPc:C 60 BHJs. Whether or not the device is fabricated as inverted [3] or non‐inverted cell influences crystal growth and, thus, phase separation during film formation. We have found that heating the substrate during BHJ film formation leads to an increase in efficiency for the inverted cell, whereas the non‐inverted device shows no improvement. While the ESI measurements showed that substrate heating facilitates phase separation of the two materials, the difference in efficiency of the different device architectures could not be explained by this. Electron diffraction data indicated that crystallinity plays a role here. Since conventional ESI and electron diffraction only provide information about material distribution and crystallinity in a two‐dimensional projection of the BHJ layers, high‐resolution electron tomography was performed to gain insight into the three‐dimensional structure. F 4 ZnPc:C 60 was co‐evaporated onto layers of neat F 4 ZnPc and C 60 , respectively. The measurements were performed under low‐dose and LN 2 ‐cryo conditions in an FEI Titan Krios. This was necessary to preserve the sample, and foremost its crystallinity, since carbon‐based materials, like C 60 , are prone to severe damage by electron irradiation. Figure 1 shows a bright‐field TEM image of the BHJ on C 60 (gold fiducials, seen in black, were used for tilt‐series alignment). All images of the acquired tilt‐series show crystalline areas such as the ones marked (A,B,C). The crystalline spacing seen here can be identified in the power spectra as characteristic for C 60 (red: 0.85 nm, green: 0.5 nm and blue: 0.44 nm). As illustrated, such crystallinity can also be visualized in high‐resolution electron tomograms, albeit only for smaller volumes at quite high magnification. To obtain a statistically significant distribution of crystallinity for different cell architecture and cell fabrication, larger volumes need to be analysed. For a given detector size, one needs to apply lower magnifications which results in lower resolution. However, the signature of pure crystals at these imaging conditions are a low variance in 3D, i.e. crystal distributions can easily be obtained from segmented 3D variance maps. A slice through the tomographic reconstruction of such samples can be seen in figure 2. Here, a BHJ film on C60 substrate is compared with a similar section through a tomogram of the BHJ on F 4 ZnPc. The gold fiducial indicates the top of the BHJ film. The homogeneous, aka crystalline areas are highlighted (red overlay). From the distribution of crystallinity we deduce, that large C 60 crystals are found in both device architectures causing a very rough film surface. In the inverted device, these crystals can extend throughout the whole film, using the polycrystalline C 60 substrate as seed for crystal growth, whereas the non‐inverted BHJ showed C 60 crystals starting somewhere in the middle of the film. Correlating this data with device performance, we find that C 60 crystals which have grown throughout the BHJ layer are crucial for efficient devices.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.