No abstract

No abstract

The aim of this study was to investigate how Brazilian dentists perceive and manage dentin hypersensitivity (DH) in their clinical routine. A 13-item questionnaire-based survey was developed and sent electronically to a convenience sample of dentists. The questionnaire assessed the personal and dental practice characteristics of the sample, the occurrence of DH in their daily clinical practice, and management strategies. The data were analyzed descriptively and together with the chi-square test (a = 0.05). A total of 353 responses were obtained from September 2017 to March 2018. Of all the respondents, 62% were females, 49.9% reported fewer than five years of dental practice, and 70.5% were self-identified as private practitioners. Most of the dentists reported an estimated frequency (30-60%) of patients with DH in their practice. The most frequently cited (91.79%) trigger of DH was air blast and/or scratching with a probe. The first-choice strategy to manage DH was a dentin desensitizer (48.16%). The number of years in clinical practice did not influence DH relapse frequency (p = 0.76) significantly, or consider DH treatment as a problem (p = 0.22). The present findings indicate that, regardless of clinical experience, dentists in Brazil still consider DH management a challenge in their daily dental practice. In addition, the results suggest that guidelines should be developed to disseminate the available knowledge regarding this condition in ways that may influence decision-making processes among practitioners.

The properties of composite resins can be influenced by light activation, depending primarily on the performance of the curing unit. The aim of this study was to evaluate how different battery levels of a cordless light-emitting diode (LED) unit influence the properties of a nanofilled composite resin. First, the battery voltage and light intensity of the cordless LED unit were individually checked for all light-curing cycles. Then, composite resin discs were prepared and light-cured at different battery levels: high level (HL, 100%), medium level (ML, 50%), and low level (LL, 10%). The degree of conversion, diametral tensile strength, sorption, and solubility of the specimens were tested. Data were checked for homoscedasticity and submitted to one-way analysis of variance followed by Tukey honestly significant difference and Pearson correlation tests (p<0.05). The battery voltage and light intensity varied significantly among the groups (p<0.001). The LL group presented a lower degree of conversion than the HL and ML groups (p<0.001), which shower similar results (p=0.182). Lower diametral tensile strength was also verified for the LL group when compared with the HL and ML groups (p<0.001), which presented no difference (p=0.052). Positive correlation was observed between the light intensity and the parameters studied, with the exception of sorption and solubility (p<0.001). The ML and LL groups showed higher sorption than the HL group (p <0.001), but no difference was verified between the first two groups (p=0.535). No significant differences were found for solubility between the ML and LL groups (p=0.104), but the HL group presented lower values (p<0.001). The different battery levels of the cordless LED curing unit influenced all the properties of the nanofilled composite resin evaluated.

No abstract

ABSTRACT:The aim of this study was to analyze the biomechanical behavior of lower premolars regarding the non-carious cervical lesion (NCCL) depth, load type and restoration status, using finite element analysis. Twodimensional virtual model simulating a healthy lower premolar were created using the CAD software. Based on this image, five models were generated: healthy (H), three types of NCCLs: small lesion (SL -0.5 mm deep), medium lesion (ML -1.0 mm), deep lesion (DL -1.5 mm), and restored lesion (RL). The models were export to a CAE software (ANSYS Finite Element Analysis Software), the areas of all structures were plotted and each model was meshed using a control mesh device. All of the virtual models were subjected to two occlusal load types, (100N each): occlusal load (OL) and buccal load (BL) on buccal cusp. The magnitude and the stress distribution were obtained using the von Mises and maximum principal stress criteria (σ1), in MPa. The quantitative analysis of stress (MPa) was identified at three points of the NCCLs: enamel surface on its upper wall , dentin at the bottom wall and dentin on the lower wall. The results showed a direct relation between sequential removal of cervical structure and higher stress concentration for any groups and for both loads types. For OL the highest value of stress was 8.8 MPa for DL on upper wall of NCCLs.The BL exhibited higher stress values in comparison to the OL for all models.In addtion, the BL was responsible for providing the highest stress accumulation on the bottom wall, 38.2 MPa for DL. The restoration with composite resin was able to restore a stress distribution close to the healthy model, for both load types. In conclusion, the extent of non-carious cervical lesion and loading conditions influenced the stress distribution pattern of lower premolar. The outer load seems to be more critical in affecting the biomechanical behavior of lower premolars, regardless of the lesion size. The restoration of NCCLs with composite resin appears to recover the biomechanical behavior, similar to healthy model.

Clinical Relevance Irradiance may decrease as the light-emitting diode (LED) is discharged. Therefore, the LED must be charged carefully to prevent the possibility of influencing the chemical, mechanical, and physical properties of composite resin.

Os problemas que englobam a saúde bucal, incluindo a doença periodontal, têm sido cada vez mais reconhecidos como importantes precursores de consequências negativas no desempenho de atividades diárias e na qualidade de vida dos indivíduos. Esse fato se torna ainda mais relevante quando se trata da saúde de mulheres gestantes e do feto em desenvolvimento que pode nascer prematuramente ou com baixo peso. O objetivo deste trabalho é avaliar a inter-relação entre a doença periodontal e a gravidez caracterizando sua associação com o pré-natal odontológico e a saúde do bebê. Trata-se de uma revisão narrativa da literatura, visando identificar quais os fatores associados à odontologia e ao pré-natal odontológico. Como critérios de inclusão foram utilizados artigos publicados nos últimos dez anos e disponibilizados em inglês e português empregando as palavras chaves odontologia e gravidez; odontologia e pré-natal odontológico; odontologia e pré-natal e doenças periodontais. Concluiu-se que a saúde bucal materna influencia diretamente na sua própria saúde como um todo, mas também na saúde do bebê. Assim, é notória a importância de se realizar o pré-natal odontológico para prevenção de patologias bucais e sistêmicas, além de também evitar partos prematuros e com baixo peso ao nascer.