We report on the preparation and characterization, under optical pump, of second-order one-dimensional distributed feedback (DFB) lasers based on polystyrene films doped with a perylenediimide derivative, as active media. The DFB gratings were engraved on the substrates (SiO2) by thermal nanoimprint lithography, followed by reactive ion etching. Laser emission wavelength was tuned from 554 to 583 nm by changing film thickness (h) between 240 and 1200 nm. The effect on the performance (emission wavelength, threshold, slope efficiency, number of modes, and spectral shape) of varying the grating depth (d) from 30 to 240 nm, for the whole range of h values, has been investigated. Although there is extensive work in the literature aiming to tune the emission wavelength of organic DFB lasers by h variation, the effect of changing d systematically has not been previously studied. Experimental results have been interpreted by models that take into account the presence of the grating by averaging either h or the effective refractive index. Single-mode emission (λ0) was observed for h < 1000 nm, while for thicker films lasing appeared at two different wavelengths (λ0 and λ1). Models indicate that λ0 and λ1 correspond to the TE0 and TE1 waveguide modes, respectively. It was found that d plays an important role in determining the DFB thresholds and slope efficiencies for two h regimes: (i) For h < 350 nm, lowest thresholds and highest slopes efficiencies were obtained with the shallower gratings; and (ii) for h > 1000 nm, d affects significantly the losses associated with the TE1 mode, so single mode emission was achieved at λ0 or at λ1 for deep and shallow gratings, respectively. Finally, the shape of the emission spectra, both below and above threshold, has also been analyzed in order to clarify the physical mechanisms responsible for the existence of gain. Bragg dips were observed in the spectra below threshold only for devices with d/h larger than around 0.3 and their width increased with increasing d/h. In these cases, single-mode DFB emission appeared at the long-wavelength edge of the Bragg dip, indicating that index-coupling modulation contributes significantly to the gain process. On the other hand, for smaller d/h values, Bragg dips became too small to be detected, so gain coupling becomes the dominant mechanism accounting for the presence of gain.

No abstract

We present an efficient Linear Minimum Mean Square Error (LMMSE) method for reconstructing full color images from single sensor Color Filter Array (CFA) data. We use a representative set of full color images to estimate the joint spatial-chromatic covariance among pixel color components. Then, we derive from it a set of joint color-space, small linear kernels which predict the missing color samples as linear combinations of their neighbor observed samples. The color arrangement of the local mosaic varies with the window's location, and this results into a different predictor for every local mosaic and color sample. As an extension, we include blur and noise in the training process, obtaining localized mosaic-constrained Wiener estimators that partially compensate for these degradations. We show that this simple method provides an excellent trade-off between performance and computational cost.

In this work we present a surface plasmon resonance sensor based on enhanced optical transmission through sub-wavelength nanohole arrays. This technique is extremely sensitive to changes in the refractive index of the surrounding medium which result in a modulation of the transmitted light. The periodic gold nanohole array sensors were fabricated by high-throughput thermal nanoimprint lithography. Square periodic arrays with sub-wavelength hole diameters were obtained and characterized. Using solutions with known refractive index, the array sensitivities were obtained. Finally, protein absorption was monitored in real-time demonstrating the label-free biosensing capabilities of the fabricated devices.

Metallic nanohole arrays have shown their potential as sensing tools. Important research supported by sophisticated laboratory experiments have been recently carried out, that may help to develop practical devices to be implemented in the real life. To get this goal, the gap between industry and technology at the nanoscale level must be overcome. One of the major drawbacks is the quality inspection of the manufactured nanostructured surfaces to ensure a reliable sensing. In this paper we introduce an optical method, based on the Extraordinary Optical Transmission phenomenon, for an inspection of such surfaces at industrial level. Unlike usual techniques like SEM, our method gives at the same time, a quick map of the surface homogeneity together with its local plasmonic performance. Our results show that this method is reproducible and reliable as to give a "seal of identification" and quality guarantee of the manufactured surface as basic element of a sensing device.

In this research, we investigate the electromagnetic behavior of a metallic thin-film with a periodic array of subwavelength apertures when dielectric objects are located on it. The influence of size, geometry and optical properties of the objects on the transmission spectra is numerically analyzed. We study the sensitivity of this system to changes in the refractive index of the illuminated volume induced by the presence of objects with sizes from hundreds of nanometers (submicron-sized objects) to a few microns (micron-sized objects). Parameters such as the object volume within the penetration depth of the surface plasmon in the buffer medium or the contact surface between the object and the nanostructured substrate strongly affect the sensitivity. The proposed system models the presence of objects and their detection through the spectral shifts undergone by the transmission spectra. Also, we demonstrate that these can be used for obtaining information about the refractive index of a micron-sized object immersed in a buffer and located on the nanostructured sensitive surface. We believe that results found in this study can help biomedical researchers and experimentalists in the process of detecting and monitoring biological organisms of large sizes (notably, cells).

Laser transmission welding (LTW) of thermoplastics is a direct bonding technique already used in different industrial applications sectors such as automobiles, microfluidics, electronics, and biomedicine. LTW evolves localized heating at the interface of two pieces of plastic to be joined. One of the plastic pieces needs to be optically transparent to the laser radiation whereas the other part has to be absorbent, being that the radiation produced by high power diode lasers is a good alternative for this process. As consequence, a tailored laser system has been designed and developed to obtain high quality weld seams with weld widths between 0.7 and 1.4 mm. The developed laser system consists of two diode laser bars (50 W per bar) coupled into an optical fiber using a nonimaging solution: equalization of the beam parameter product (BPP) in the slow and fast axes by a pair of step-mirrors. The power scaling was carried out by means of a multiplexing polarization technique. The analysis of energy balance and beam quality was performed considering ray tracing simulation (ZEMAX®) and experimental validation. The welding experiments were conducted on acrylonitrile/butadiene/styrene (ABS), a thermoplastic frequently used in automotive, electronics and aircraft applications, doped with two different concentrations of carbon nanotubes (0.01% and 0.05% CNTs). Quality of the weld seams on ABS was analyzed in terms of the process parameters (welding speed, laser power and clamping pressure) by visual and optical microscope inspections. Mechanical properties of weld seams were analyzed by mechanical shear tests. High quality weld seams were produced in ABS, revealing the potential of the laser developed in this work for a wide range of plastic welding applications.

In the present work thermal nanoimprint lithography of various commercial thermoplastic resists as matrixes for perylenediimides (PDIs) has been studied. This fabrication method reduced the number of fabrication steps, and therefore, the cost of the obtained distributed feedback (DFB) lasers. The optical properties of these devices are analyzed, aiming to optimize their performance. Thermal AbstractIn the present work thermal-nanoimprint lithography of various commercial