Abstract. "Micromorph" tandem solar cells consisting of a microcrystalline silicon bottom cell and an amorphous silicon top cell are considered as one of the most promising new thin-film silicon solar-cell concepts. Their promise lies in the hope of simultaneously achieving high conversion efficiencies at relatively low manufacturing costs. The concept was introduced by IMT Neuchâtel, based on the VHF-GD (very high frequency glow discharge) deposition method. The key element of the micromorph cell is the hydrogenated microcrystalline silicon bottom cell that opens new perspectives for low-temperature thin-film crystalline silicon technology. According to our present physical understanding microcrystalline silicon can be considered to be much more complex and very different from an ideal isotropic semiconductor. So far, stabilized efficiencies of about 12% (10.7% independently confirmed) could be obtained with micromorph solar cells. The scope of this paper is to emphasize two aspects: the first one is the complexity and the variety of microcrystalline silicon. The second aspect is to point out that the deposition parameter space is very large and mainly unexploited. Nevertheless, the results obtained are very encouraging and confirm that the micromorph concept has the potential to come close to the required performance criteria concerning price and efficiency.The justification of worldwide, intensified research on thinfilm solar cells is not based on a lack of success in the efficiency performance of wafer-based silicon or GaAs technologies. It is based on a lack of hope in the cost reduction potential of wafer-based technology. Indeed, in order to render photovoltaics a competitive energy source in future, it is imperative to adopt the approach of low-cost solar cells.

No abstract

Recently the authors have demonstrated that compensated or “midgap” intrinsic hydrogenated microcrystalline silicon (μc-Si:H), as deposited by the Very High Frequency Glow Discharge (VHF-GD) technique, can be used as active layer in p-i-n solar cells. Compared to amorphous silicon (a-Si:H), μc-Si:H was found to have a significantly lower energy bandgap of around 1 eV. The combination of both materials (two absorbers with different gap energies) leads to a “real” tandem cell structure, which was called the “micromorph” cell. Micromorph cells can make better use of the sun's spectrum in contrast to conventional double-stacked a-Si:H / a-Si:H tandems.The present study will show that the compensation technique (involving boron “microdoping”) used sofar for obtaining midgap μc-Si:H can be replaced by the application of a gas purifier. The use of this gas purifier has a beneficial influence on the transport properties of undoped intrinsic μc-Si:H. By this procedure, increased cell efficiencies in both, single microcrystalline silicon p-i-n as well as micromorph cells could be obtained. In the first case 7.7 % stable, and in the second case 13.1% initial efficiency could be achieved under AM1.5 conditions. Preliminary light-soaking experiments performed on the tandem cells indicate that microcrystalline silicon could contribute to an enhancement of the stable efficiency performance. Micromorph cell manufacturing is fully compatible to a-Si:H technology; however, its deposition rate is still too low. With further increase of the rate, a similar cost reduction potential like in a-Si:H technology can be extrapolated.

bstractRecently, we have demonstrated that intrinsic hydrogenated microcrystalline silicon, as deposited by the very high frequency glow-discharge technique, can be used as the active layers of p-i-n solar cells. Our microcrystalline silicon Ž represents a new form of thin film crystalline silicon that can be deposited in contrast to any other approach found in . literature at substrate temperatures as low as 2008C. The combination of amorphous and microcrystalline material leads to a 'real' silicon-based tandem structure, which we label 'micromorph' cell. Meanwhile, stabilised efficiencies of 10.7% have been confirmed. In this paper, we present an improved micromorph tandem cell with 12% stabilised efficiency measured under outdoor conditions. Dark conductivity and combined SIMS measurements performed on intrinsic microcrystalline silicon layers reveal a post-oxidation of the film surface. However, a perfect chemical stability of entire microcrystalline cells as well as micromorph cells is presented. Variations of the pri interface treatment show that an increase of the open circuit voltages from 450 mV up to 568 mV are achievable for microcrystalline cells, but such devices have reduced fill factors.

No abstract