Three non‐bridged dimethylzirconocene complexes; i.e., bis(η5‐cyclopentadienyl)dimethylzirconium (1), bis(η5‐tert‐butyl‐cyclopentadienyl)dimethylzirconium (2), bis(η5‐indenyl)dimethylzirconium (3), and the chiral zirconocene rac‐ethylenebis(η5‐indenyl)dimethylzirconium (4) were synthesized and used as catalysts for the polymerization of methyl methacrylate, MMA, combined with tris(pentafluorophenyl)borate (A) or tetrakis(pentafluorophenyl)borate dimethylanilinum salt (B) in the presence of ZnEt2. The evolution of the polymerization characteristics; i.e., molecular weight, molecular‐weight distribution, and yield were examined for the above systems. The influence of the nature of the solvent was also investigated. The aggregation behavior, the steric hindrance, and the lipophilicity of the active catalytic systems are the most important parameters determining the polymerization characteristics. The tacticity of the products is reported and the influence of the catalyst structure is discussed. Finally, the polymerization of other methacrylates (alkyl = butyl, hexyl, decyl, stearyl, and sec‐butyl), was conducted and the effect of the nature of the alkyl ester group on the molecular and structural characteristics was established.
Well-defined graft copolymers with poly(methyl methacrylate) backbone and poly(styrene) (PS), poly(isoprene) (PI), or poly(dimethylsiloxane) (PDMS) branches were synthesized by combining anionic and metallocene catalyzed polymerization. The synthetic strategy involves the preparation of methacryloyl macromonomers of PS, PI, and PDMS by anionic polymerization, followed by copolymerization with methyl methacrylate using the highly reactive catalytic system Cp 2ZrMe2/B(C6F5)3/ZnEt2. The macromonomers and the fractionated graft copolymers were characterized by size exclusion chromatography, low-angle laser light scattering, and 1 H NMR spectroscopy.
Polymerization of methyl methacrylate (MMA) by the three component catalytic system Cp2ZrMe2/B(C6F5)3/ZnEt2 (1), in toluene, under thoroughly purified conditions, was found to produce polymers of high molecular weights (M w > 60 × 103), low polydispersities (M w/M n = 1.12−1.22) and almost quantitative yields. The polymerization process is characterized by a pronounced induction period followed by a rapid and constant rate of polymerization. The molecular weight of PMMA increases by increasing the conversion and is proportional to the ratio of [MMA]0/[Zr]0, while M w/M n remains intact, meaning that the present polymerization proceeds in a well-controlled fashion. Evidence for effects of [ZnEt2] and temperature in the molecular characteristics of the final products are also presented in this study. Moreover, the catalytic system 1 was found to catalyze the polymerization of other alkyl methacrylates (alkyl = n-butyl, n-hexyl) to high molecular weight syndiotactic materials, with narrow molecular weight distribution, in very high conversion. Well-controlled copolymerization of MMA with n-hexyl methacrylate was successful by the effective catalytic action of 1, leading to multiblock polymeric structures. Copolymerization of MMA with stearyl methacrylate was also achieved, with the above-mentioned catalytic system. Evidence for the aggregation of the polymeric products in THF and toluene solutions was found by static and dynamic light scattering. The comparison of the polymerization results of this work with other studies clearly shows that in order to obtain improved molecular characteristics, thorough purification protocols should be applied.
Graft copolymers having poly(methyl methacrylate), PMMA, backbone and polystyrene, PS, polyisoprene, PI, poly(ethylene oxide), PEO, poly(2-methyl-1,3-pentadiene), P2MP, and PS-b-PI branches were prepared using the macromonomer methodology and high-vacuum techniques. The methacrylic macromonomers, mMM, were synthesized by anionic polymerization, whereas their homopolymerization and copolymerization with MMA were performed by metallocene catalysts. Relatively high macromonomer conversions were obtained in all cases. The parameters affecting the polymerization characteristics were examined. Well-defined poly(butyl methacrylate)-b-poly(methyl methacrylate) block copolymers were prepared for the first time by sequential addition of monomers starting from n-butyl methacrylate. The samples were characterized by size exclusion chromatography, SEC, 1 H and 13 C NMR spectroscopy, low-angle laser light scattering, LALLS, and differential scanning calorimetry, DSC.
Statistical copolymers of methyl methacrylate (MMA) with n‐butyl‐, s‐butyl, t‐butyl‐, n‐hexyl‐, decyl‐, stearyl‐, allyl‐, trimethylsilyl‐ and trimethylsilyloxyethyl methacrylate were prepared by zirconocene‐catalyzed copolymerization. The reactivity ratios of MMA copolymers with butyl‐, hexyl‐, and stearyl methacrylate were estimated using the Finemann–Ross, the inverted Finemann–Ross, and the Kelen–Tüdos graphical methods. Structural parameters of the copolymers were obtained from the calculated dyad sequences, derived by using the reactivity ratios. The effect of the nature of the methacrylate ester group and the catalytic system used on the copolymer structure is discussed. The glass‐transition temperature (Tg) values of MMA copolymers with butyl‐ and hexyl methacrylate were measured and examined in the frame of several theoretical equations, allowing the prediction of these Tg values. The best fit was obtained using Barton and Johnston equations, taking the monomer sequence distribution of the copolymers into account. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3761–3774, 2004
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.