Technological deployment of organic photovoltaic modules requires improvements in device light-conversion efficiency and stability while keeping material costs low. Here we demonstrate highly efficient and stable solar cells using a ternary approach, wherein two non-fullerene acceptors are combined with both a scalable and affordable donor polymer, poly(3-hexylthiophene) (P3HT), and a high efficiency, low band-gap polymer in a single-layer bulk-heterojunction devices. The addition of a strongly absorbing small molecule acceptor into a P3HT-based non-fullerene blend increases the device efficiency up to 7.7 ± 0.1% without any solvent additives. The improvement is assigned to changes in microstructure that reduces charge recombination and increases the photovoltage, and to improved light harvesting across the visible region. The stability of P3HT-based devices in ambient conditions is also significantly improved relative to polymer:fullerene devices. Combined with a low band gap donor polymer (PBDTTT-EFT, also known as PCE10), the two mixed acceptors also lead to solar cells with 11.0 ± 0.4% efficiency and a high open-circuit voltage of 1.03 ± 0.01V.Currently, the materials used in organic photovoltaics (OPV) are dominated by fullerene acceptors in combination with low band gap donor polymers which typically require complex and multi-step syntheses. [1][2][3][4][5] However, the commercialization of OPV requires the availability of inexpensive materials in large quantities such as poly(3-hexylthiophene) (P3HT). P3HT is readily scalable via flow or micro-reactor synthesis, even using 'green' solvents, whilst retaining a high degree of control over molecular weight and regioregularity. 6 The P3HT:60PCBM blend exhibits one of the most robust microstructures within OPV. [7][8][9] However, it has a limited open-circuit voltage (Voc) and short-circuit current (Jsc) in photovoltaic devices. 10 We have recently shown that solar cells using an alternative small molecule non-fullerene acceptor (NFA), IDTBR, when mixed with P3HT, can achieve power conversion efficiencies of up to 6.4%. 11 These results have revived interest in the use of P3HT for high performing devices and non-fullerene acceptors. [12][13][14][15][16][17][18] The combination of stability, cost and performance for P3HT:NFA devices, make them a compelling choice for commercialization of OPV compared to devices using fullerenes, for which the high costs and energy involved are prohibitive for large scale production.Recently, multi-component heterojunctions (ternary or more) have emerged as a promising strategy to overcome the power conversion efficiency (PCE) bottleneck associated with binary bulk-heterojunction (BHJ) solar cells. 3,4,[19][20][21][22][23]24 However, simultaneous increase in the Voc, Jsc and FF is a challenge in the ternary approach because of the trade-off between photocurrent and voltage. 23,25,26 Reports show ternary blends using fullerene acceptors, where the Voc is increased using a second acceptor (A2) with a higher electron affin...

The primary driver for development of organic photovoltaic (OPV) technologies is the prospect of very low cost module manufacture leading to affordable solar electricity. This paper presents an economic assessment of OPV based on an existing pre-industrial manufacturing process and the associated detailed material inventory. Using life cycle costing techniques, the life cycle investment cost for a 1kW p , grid-connected OPV system is calculated, taking into account the materials, direct process energy, labour, balance of system components, design and maintenance costs. Assuming values for the performance ratio of the PV system, insolation level, inflation and interest rates, the levelised electricity cost (LEC) is calculated. Under an average solar irradiance of 1700 kWh/m 2 /year, typical of southern Europe, a LEC of between 0.19 V/kWh and 0.50 V/kWh was calculated for a 1kW p system, based on modules containing 7% efficient cells and assuming a 5 year module lifetime. The OPV module is found to make up the majority of the system cost while the material costs constitute the largest contribution to the cost of the OPV module. The influence of OPV module lifetime is studied using sensitivity. This paper demonstrates that competitive solar electricity from OPV is within reach if efficiencies of ca. 7% already demonstrated in lab scale devices can be achieved in large area modules and if lifetimes of at least 5 years can be achieved.

Storing electrical energy in hydrogen requires less manufacturing energy than batteries, per unit of energy dispatched over the system's lifetime.

No abstract

Organic photovoltaics is an emerging solar power technology which embodies properties such as transparency, flexibility, and rapid, roll to roll manufacture, opening the potential for unique niche applications. We report a detailed techno-economic analysis of one such application, namely the photovoltaic greenhouse, and discuss whether the unique properties of the technology can provide advantages over conventional photovoltaics. The potential for spectral selectivity through the choice of OPV materials is evaluated for the case of a photovoltaic greenhouse. The action spectrum of typical greenhouse crops is used to determine the impact on crop growth of blocking different spectral ranges from the crops. Transfer matrix optical modelling is used to assess the efficiency and spectrally resolved transparency of a variety of commercially available semi-conducting polymer materials, in addition to a non-commercial low-band-gap material with absorption outside that required for crop growth. Economic analysis suggests there could be a huge potential for OPV greenhouses if aggressive cost targets can be met. Technical analysis shows that semi-transparent OPV devices may struggle to perform better than opaque crystalline silicon with partial coverage, however, OPV devices using the low-band-gap material PMDPP3T, as well as a high efficiency mid-band-gap polymer PCDTBT, can demonstrate improved performance in comparison to opaque, flexible thin-film modules such as CIGS. These results stress the importance of developing new, highly transparent electrode and interlayer materials, along with high efficiency active layers, if the full potential of this application is going to be realised.