A new type of amino polar binder with 3D network flexibility structure for high energy Li-S batteries is synthesized and successfully used with commercial sulfur powder cathodes. The binder shows significant performance improvement in capacity retention and high potential for practical application, which arouse the battery community's interest in the commercial application of high energy Li-S battery.
With over fivefold energy capacity, sulfur demonstrates superior advantages over current commercial intercalation compound (LiCoO 2 and LiFePO 4 ) cathode materials. [3][4][5] Despite its considerable advantages, the practical application of Li-S battery has been hindered by poor cycle life due to the shuttle effect, leading to quick capacity decay due to the loss of active materials and an low Coulombic efficiency. [6,7] Moreover, the insulating nature of S/Li 2 S and as large as 78% volume expansion of sulfur cathode when initial state S (2.03 g cm −3 ) is fully converted to final state Li 2 S (1.66 g cm −3 ) result in rapid capacity fading and short cycle life due to the low utilization of active materials and poor electrical contact between sulfur particles and conductive additives. [8,9] Aiming to address these negative impact of at least some of the detrimental processes described above for realizing commercial application of highenergy Li-S battery, various considerable strategies have been focused on cathode material modification including N-doped materials, [10][11][12] porous materials, [13] hierarchical materials, [14] metal oxides [15,16] transition metal disulfides, [17] and functional separator modification, [18,19] as well as employment of solid or As one of the important ingredients in lithium-sulfur battery, the binders greatly impact the battery performance. However, conventional binders have intrinsic drawbacks such as poor capability of absorbing hydrophilic lithium polysulfides, resulting in severe capacity decay. This study reports a new type of binder by polymerization of hydrophilic poly(ethylene glycol) diglycidyl ether with polyethylenimine, which enables strongly anchoring polysulfides for highperformance lithium sulfur batteries, demonstrating remarkable improvement in both mechanical performance for standing up to 100 g weight and an excellent capacity retention of 72% over 400 cycles at 1.5 C. Importantly, in situ micro-Raman investigation verifies the effectively reduced polysulfides shuttling from sulfur cathode to lithium anode, which shows the greatly suppressed shuttle effect by the polar-functional binder. X-ray photoelectron spectroscopy analysis into the discharge intermediates upon battery cycling reveals that the hydrophilic binder endows the sulfur electrodes with multidimensional Li-O, Li-N, and S-O interactions with sulfur species to effectively mitigate lithium polysulfide dissolution, which is theoretically confirmed by density-functional theory calculations.
A sustainable route from the biomass byproduct okara as a natural nitrogen fertilizer to high-content N-doped carbon sheets is demonstrated. The as-prepared unique structure exhibits high specific capacity (292 mAh g(-1) ) and extremely long cycle life (exceeding 2000 cycles). A full battery is devised for the practical use of materials with a flexible/wearable LED screen.
Safety, nontoxicity, and durability directly determine the applicability of the essential characteristics of the lithium (Li)‐ion battery. Particularly, for the lithium–sulfur battery, due to the low ignition temperature of sulfur, metal lithium as the anode material, and the use of flammable organic electrolytes, addressing security problems is of increased difficulty. In the past few years, two basic electrolyte systems are studied extensively to solve the notorious safety issues. One system is the conventional organic liquid electrolyte, and the other is the inorganic solid‐state or quasi‐solid‐state composite electrolyte. Here, the recent development of engineered liquid electrolytes and design considerations for solid electrolytes in tackling these safety issues are reviewed to ensure the safety of electrolyte systems between sulfur cathode materials and the lithium‐metal anode. Specifically, strategies for designing and modifying liquid electrolytes including introducing gas evolution, flame, aqueous, and dendrite‐free electrolytes are proposed. Moreover, the considerations involving a high‐performance Li+ conductor, air‐stable Li+ conductors, and stable interface performance between the sulfur cathode and the lithium anode for developing all‐solid‐state electrolytes are discussed. In the end, an outlook for future directions to offer reliable electrolyte systems is presented for the development of commercially viable lithium–sulfur batteries.
Fast lithium ion transport with a high current density is critical for thick sulfur cathodes, stemming mainly from the difficulties in creating effective lithium ion pathways in high sulfur content electrodes. To develop a high-rate cathode for lithium-sulfur (Li-S) batteries, extenuation of the lithium ion diffusion barrier in thick electrodes is potentially straightforward. Here, a phyllosilicate material with a large interlamellar distance is demonstrated in high-rate cathodes as high sulfur loading. The interlayer space (≈1.396 nm) incorporated into a low lithium ion diffusion barrier (0.155 eV) significantly facilitates lithium ion diffusion within the entire sulfur cathode, and gives rise to remarkable nearly sulfur loading-independent cell performances. When combined with 80% sulfur contents, the electrodes achieve a high capacity of 865 mAh g at 1 mA cm and a retention of 345 mAh g at a high discharging/charging rate of 15 mA cm , with a sulfur loading up to 4 mg. This strategy represents a major advance in high-rate Li-S batteries via the construction of fast ions transfer paths toward real-life applications, and contributes to the research community for the fundamental mechanism study of loading-independent electrode systems.
Sodium-ion battery (SIB) is especially attractive in cost-effective energy storage device as an alternative to lithium-ion battery. Particularly, metal phosphides as potential anodes for SIBs have recently been demonstrated owing to their higher specifi c capacities compared with those of carbonaceous materials. Unfortunately, most reported metal phosphides consist of irregular particles ranged from several hundreds nanometers to tens of micrometers, thus delivering limited cyclic stability. This paper reports the sodium storage properties of additive-free Cu 3 P nanowire (CPNW) anode directly grown on copper current collector via an in situ growth followed by phosphidation method. Therefore, as a result of its structure features, CPNW anode demonstrates highly stable cycling ability with an ≈70% retention in capacity at the 260th cycle, whereas most reported metal phosphides have limited cycle numbers ranged between 30 and 150. Besides, the reaction mechanism between Cu 3 P and Na is investigated by examining the intermediate products at different charge/discharge stages using ex situ X-ray diffraction measurements. Furthermore, to explore the practical application of CPNW anode, a pouch-type Na + full cell consisting of CPNW anode and Na 3 V 2 (PO 4 ) 3 cathode is assembled and characterized. As a demonstration, a 10 cm × 10 cm light-emmiting diode (LED) screen is successfully powered by the Na + full cell. Figure 6. a) Schematic representation of the pouch-type CPNW/NVP Na + full cell. b) Cycling performance of the CPNW/NVP Na + full cell at current densities of 600 mA g −1 . c,d) Optical images showing a fl exible LED screen powered by the pouch-type CPNW/NVP Na + full cell.
wileyonlinelibrary.com
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.