No abstract

Biofilms of sulphate-reducing Desulfovibrio sp. EX265 were grown in square section glass capillary flow cells under a range of fluid flow velocities from 0.01 to 0.4 m/s (wall shear stress, tau(w), from 0.027 to 1.0 N/m(2)). In situ image analysis and confocal scanning laser microscopy revealed biofilm characteristics similar to those reported for aerobic biofilms. Biofilms in both flow cells were patchy and consisted of cell clusters separated by voids. Length-to-width ratio measurements (l(c):w(c)) of biofilm clusters demonstrated the formation of more "streamlined" biofilm clusters (l(c):w(c)=3.03) at high-flow velocity (Reynolds number, Re, 1200), whereas at low-flow velocity (Re 120), the l(c):w(c) of the clusters was approximately 1 (l(c):w(c) of 1 indicates no elongation in the flow direction). Cell clusters grown under high flow were more rigid and had a higher yield point (the point at which the biofilm began to flow like a fluid) than those established at low flow and some biofilm cell aggregates were able to relocate within a cluster, by travelling in the direction of flow, before attaching more firmly downstream.

Knowledge of bacterial transport through, and biofilm growth in, porous media is vitally important in numerous natural and engineered environments. Despite this, porous media systems are generally oversimplified and the local complexity of cell transport, biofilm formation and the effect of biofilm accumulation on flow patterns is lost. In this study, cells of the sulphate-reducing bacterium, Desulfovibrio sp. EX265, accumulated primarily on the leading faces of obstructions and developed into biofilm, which grew to narrow and block pore throats (at a rate of 12 micro m h(-1) in one instance). This pore blocking corresponded to a decrease in permeability from 9.9 to 4.9 Darcy. Biofilm processes were observed in detail and quantitative data were used to describe the rate of biofilm accumulation temporally and spatially. Accumulation in the inlet zone of the micromodel was 10% higher than in the outlet zone and a mean biofilm height of 28.4 micro m was measured in a micromodel with an average pore height of 34.9 microm. Backflow (flow reversal) of fluid was implemented on micromodels blocked with biofilm growth. Although biofilm surface area cover did immediately decrease (approximately 5%), the biofilm quickly re-established and permeability was not significantly affected (9.4 Darcy). These results demonstrate that the glass micromodel used here is an effective tool for in situ analysis and quantification of bacteria in porous media.

Aims:  Comparison of biochemical vs molecular methods for identification of microbial populations associated with failed loggerhead turtle eggs. Methods and Results:  Two biochemical (API and Microgen) and one molecular methods (16s rRNA analysis) were compared in the areas of cost, identification, corroboration of data with other methods, ease of use, resources and software. The molecular method was costly and identified only 66% of the isolates tested compared with 74% for API. A 74% discrepancy in identifications occurred between API and 16s rRNA analysis. The two biochemical methods were comparable in cost, but Microgen was easier to use and yielded the lowest discrepancy among identifications (29%) when compared with both API 20 enteric (API 20E) and API 20 nonenteric (API 20NE) combined. A comparison of API 20E and API 20NE indicated an 83% discrepancy between the two methods. Conclusions:  The Microgen identification system appears to be better suited than API or 16s rRNA analysis for identification of environmental isolates associated with failed loggerhead eggs. Significance and Impact of the Study:  Most identification methods are not intended for use with environmental isolates. A comparison of identification systems would provide better options for identifying environmental bacteria for ecological studies.

Origins of Hydrocarbon Reservoirs Oil‐Bearing Rock Formations as Microbial Habitats Microbiology of Oil‐Bearing Rocks Microbial Consequences of Oil Reservoir Exploitation Application of Microbial Technology for Exploitation of Petroleum Reservoirs

Sulphidogenic bacteria in oil reservoirs are of great economic importance in terms of souring, fouling and corrosion. Mixed cultures containing these bacteria were isolated from chalk formations in North Sea oil reservoirs. These were thermophilic cultures, growing optimally at 60°C. Oil formations are porous matrices, providing a very large surface area and ideal conditions for bacterial attachment, survival and growth. This study included assessments of sulphide production rates of thermophilic (t-)sulphidogen consortia with and without additional surfaces. The availability of a surface contributed significantly to the rate and extent of sulphide generation. Surfaces were offered in varying amounts to growing planktonic cultures: significantly more sulphide was produced from cultures in contact with a surface than from identical cultures in the absence of a surface. In another series of experiments, t-sulphidogens were added to chalk rock chips in the presence of nutrients and incubated for several months. This resulted in rapid sulphide generation, the final concentration being related to the initial nutrient concentration. Subsequent nutrient addition resulted in renewed sulphide generation. It is suggested that bacteria in reservoirs can withstand long periods of nutrient deprivation while attached within the porous rock matrix and opportunistically utilise nutrients when they become available.

No abstract

No abstract