RESUMO O trabalho visa um estudo comparativo entre a eficiência do óleo de coco babaçu (Orbignya oleifera) utilizado como inibidor verde de corrosão e um inibidor comercial testados em aço ABNT 1020 em meio contendo ácido clorídrico. A avaliação foi realizada utilizando técnicas eletroquímicas de polarização linear aliado ao Método de Extrapolação de Tafel e Espectroscopia de Impedância Eletroquímica. As concentrações dos inibidores utilizadas foram 3, 4 e 5 g/L em solução contendo ácido clorídrico (HCl) 1M. Os resultados de espectroscopia de impedância eletroquímica mostraram que o Orbignya oleifera atua como inibidor de adsorção e que sua eficiência de inibição (56,45%) é superior comparado a eficiência do inibidor comercial (36,08%) na concentração de 3 g/L, uma vez que apresentou maior resistência de transferência de carga (47,3Ω) em comparação ao inibidor HPAA (32,23Ω). Os resultados de polarização linear mostraram que o óleo de Orbignya oleífera aumentou a eficiência de inibição no aço ABNT 1020 em solução de HCl 1M nas concentração de 3 e 4 g/L. A máxima eficiência inibidora do Orbignya oleífera neste ensaio foi de 48%, que pode estar associada a composição química desse óleo, na qual consta a presença do ácido láurico com concentração de 47%, o que pode ter contribuído para uma camada de inibição mais eficiente.
Hot-formed components are constantly exposed to hostile environments with corrosive substances. Microstructural changes caused by thermomechanical processing can be predicted to increase the corrosion resistance of austenitic stainless steels. The objective of this study is to understand the relationship between the dynamic softening mechanisms and corrosion resistance, thus optimizing the hot-forming process. In the current work, the dynamic recrystallization (DRX) behavior of AISI 316 L austenitic stainless steel was studied in the temperature range of 1273-1423 K and strain-rate range of 0.1-5.0 s −1 using physical simulation. Subsequently, potentiodynamic polarization tests and scanning electron microscopy were performed on the hot-deformed samples to investigate the influence of temperature and strain-rate on the corrosion resistance and mechanical properties. The results indicated that the DRX fractions increased under low-temperature and high strain-rate conditions, resulting in grain refinement. The potentiodynamic polarization tests indicated that the dynamically recovered samples demonstrated high resistance to corrosion compared with the DRX samples. The best route found for the investigated alloy was for the strain to be applied at a temperature of 1423 K and a strain rate of 0.1 s −1 .
This study investigated the softening mechanisms of the AISI 410 martensitic stainless steel during torsion simulation under isothermal continuous in the temperature range of 900 to 1150 °C and strain rates of 0.1 to 5.0s -1 . In the first part of the curves, before the peak, the results show that the critical (ε c ) and peak (ε p ) strains are elevated for higher strain rate and lower temperatures contributing for higher strain hardening rate (h). Moreover, this indicated that dynamic recrystallization (DRX) and dynamic recovery (DRV) are not effective in this region. After the peak, the reductions in stresses are associated to the different DRX/DRV competitions. For lower temperatures and higher strain rates there is a delay in the DRX while the DRV is acting predominantly (with low Avrami exponent (n) and high t 0.5 ). The steady state was reached after large strains showing DRX grains, formation of retained austenite and the presence of chromium carbide (Cr 23 C 6 ) and ferrite δ at the martensitic grain boundaries. These contribute for impairing the toughness and ductility on the material. The constitutive equations at the peak strain indicated changes in the deformation mechanism, with variable strain rate sensitivity (m), which affected the final microstructure.
RESUMO Em dutos que operam em regime turbulento, o processo corrosivo é acelerado e diretamente responsável por inúmeros prejuízos em plantas industriais, tais como paradas nas linhas de produção, falhas em equipamentos e elevados custos de manutenção. Embora haja poucos estudos laboratoriais nesta condição de escoamento, há um consenso entre inúmeros pesquisadores que o monitoramento e investigações nesta condição são essenciais, uma vez que simulam condições representativas da realidade industrial. Este trabalho investigou a influência do fluxo do meio eletrolítico sobre os parâmetros eletroquímicos do aço ABNT 1020 em solução NaCl 3% submetido a diferentes velocidades (0,21, 0,42, 0,62 e 0,84 m.s-1), relacionando os resultados obtidos por Espectroscopia de Impedância Eletroquímica (EIE) e Polarização Potenciodinâmica Linear (PPL). Os ensaios eletroquímicos foram realizados a partir de uma plataforma experimental construída para tal finalidade e acoplada às conexões do potenciostato, a fim de se obter curvas experimentais enquanto o eletrólito fluía dentro da célula e interagia com a superfície do metal. Os resultados mostraram que a variação da velocidade provoca mudanças notáveis nos principais parâmetros do ensaio e que as técnicas eletroquímicas corroboraram entre si mesmo em condições turbulentas de escoamento na plataforma de testes.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.