Magnetic triggering of edge localized modes (ELMs) was reported first from TCV in ohmic plasmas showing type-III ELMs. This method, showing successful locking of the ELM frequency to an imposed vertical plasma oscillation, has now also been demonstrated in the ITER-relevant type-I ELM regime in ASDEX Upgrade. Our experiments showed the ELM frequency becoming identical to the driving frequency in steady state for an applied motion of only about twice the value caused by an intrinsic ELM event. Triggered ELMs still showing clear type-I features were found when the plasma downshift velocity reached its maximum, corresponding to the lowest edge current value. This is the opposite of the behaviour expected from the peelingballooning nature attributed to the ELM boundary and to TCV observations. The reason for this behaviour is not yet clear.

Recent experiments at ASDEX Upgrade have achieved advanced scenarios with high β N (>3) and confinement enhancement over ITER98(y, 2) scaling, H H98y2 = 1.1-1.5, in steady state. These discharges have been obtained in a modified divertor configuration for ASDEX Upgrade, allowing operation at higher triangularity, and with a changed neutral beam injection (NBI) system, for a more tangential, off-axis beam deposition. The figure of merit, β N H ITER89-P , reaches up to 7.5 for several seconds in plasmas approaching stationary conditions. These advanced tokamak discharges have low magnetic shear in the centre, with q on-axis near 1, and edge safety factor, q 95 in the range 3.3-4.5. This q-profile is sustained by the bootstrap current, NBI-driven current and fishbone activity in the core. The off-axis heating leads to a strong peaking of the density profile and impurity accumulation in the core. This can be avoided by adding some central heating from ion cyclotron resonance heating or electron cyclotron resonance heating, since the temperature profiles are stiff in this advanced scenario (no internal transport barrier). Using a combination of NBI and gas fuelling line, average densities up to 80-90% of the Greenwald density are achieved, maintaining good confinement. The best integrated results in terms of confinement, stability and ability to operate at high density are obtained in highly shaped configurations, near double null, with δ = 0.43. At the highest densities, a strong reduction of the edge localized mode activity similar to type II activity is observed, providing a steady power load on the divertor, in the range of 6 MW m −2 , despite the high input power used (>10 MW).

The ASDEX Upgrade (AUG) programme is directed towards physics input to critical elements of the ITER design and the preparation of ITER operation, as well as addressing physics issues for a future DEMO design. Since 2015, AUG is equipped with a new pair of 3-strap ICRF antennas, which were designed for a reduction of tungsten release during ICRF operation. As predicted, a factor two reduction on the ICRF-induced W plasma content could be achieved by the reduction of the sheath voltage at the antenna limiters via the compensation of the image currents of the central and side straps in the antenna frame. There are two main operational scenario lines in AUG. Experiments with low collisionality, which comprise current drive, ELM mitigation/suppression and fast ion physics, are mainly done with freshly boronized walls to reduce the tungsten influx at these high edge temperature conditions. Full ELM suppression and non-inductive operation up to a plasma current of I p = 0.8 MA could be obtained at low plasma density. Plasma exhaust is studied under conditions of high neutral divertor pressure and separatrix electron density, where a fresh boronization is not required. Substantial progress could be achieved for the understanding of the confinement degradation by strong D puffing and the improvement with nitrogen or carbon seeding. Inward/outward shifts of the electron density profile relative to the temperature profile effect the edge stability via the pressure profile changes and lead to improved/decreased pedestal performance. Seeding and D gas puffing are found to effect the core fueling via changes in a region of high density on the high field side (HFSHD). The integration of all above mentioned operational scenarios will be feasible and naturally obtained in a large device where the edge is more opaque for neutrals and higher plasma temperatures provide a lower collisionality. The combination of exhaust control with pellet fueling has been successfully demonstrated. High divertor enrichment values of nitrogen E N ⩾ 10 have been obtained during pellet injection, which is a prerequisite for the simultaneous achievement of good core plasma purity and high divertor radiation levels. Impurity accumulation observed in the all-metal AUG device caused by the strong neoclassical inward transport of tungsten in the pedestal is expected to be relieved by the higher neoclassical temperature screening in larger devices.

No abstract