No abstract

Key questions in fault reactivation in shales relate to the potential for enhanced fluid transport through previously low‐permeability aseismic formations. Here we explore the behavior of a 20 m long N0‐to‐170°, 75‐to‐80°W fault in shales that is critically stressed under a strike‐slip regime (σ1 = 4 ± 2 MPa, horizontal and N162° ± 15°E, σ2 = 3.8 ± 0.4 MPa and σ3 = 2.1 ± 1 MPa, respectively 7–8° inclined from vertical and horizontal and N72°). The fault was reactivated by fluid pressurization in a borehole using a straddle packer system isolating a 2.4 m long injection chamber oriented‐subnormal to the fault surface at a depth of 250 m. A three‐dimensional displacement sensor attached across the fault allowed monitoring fault movements, injection pressure and flow rate. Pressurization induced a hydraulic diffusivity increase from ~2 × 10−9 to ~103 m2 s−1 associated with a complex three‐dimensional fault movement. The shear (x‐, z‐) and fault‐normal (y‐) components (Ux, Uy, and Uz) =  (44.0 × 10−6 m, 10.5 × 10−6 m, and 20.0 × 10−6 m) are characterized by much larger shear displacements than the normal opening. Numerical analyses of the experiment show that the fault permeability evolution is controlled by the fault reactivation in shear related to Coulomb failure. The large additional fault hydraulic aperture for fluid flow is not reflected in the total normal displacement that showed a small partly contractile component. This suggests that complex dilatant effects estimated to occur in a plurimeter radius around the injection source affect the flow and slipping patch geometries during fault rupture, controlling the initial slow slip and the strong back slip of the fault following depressurization.

Conventional triaxial tests were performed on three sets of samples of Tournemire shale along different orientations relative to bedding (0°, 45°, and 90°). Experiments were carried out up to failure at increasing confining pressures ranging from 2.5 to 160 MPa, at strain rates ranging between 3 × 10−7s−1 and 3 × 10−5s−1. This allowed us to determine the entire anisotropic elastic compliance matrix as a function of confining pressure. Results show that the orientation of principal stress relative to bedding plays an important role on the brittle strength, with 45° orientation being the weakest. We fit our results with a wing crack micromechanical model and an anisotropic fracture toughness. We found low values of internal friction coefficient and apparent friction coefficient in agreement with friction coefficient of clay minerals (between 0.2 and 0.3) and values of KIc comparable to that already published in the literature. We also showed that strain rate has a strong impact on peak stress and that dilatancy appears right before failure and hence highlighting the importance of plasticity mechanisms. Although brittle failure was systematically observed, stress drops and associated slips were slow and deformation always remained aseismic (no acoustic emission were detected). This confirms that shales are good lithological candidates for shallow crust aseismic creep and slow slip events.

We describe the structure, microstructure, and petrophysical properties of fault rocks from two normal fault zones formed in low-porosity turbiditic arkosic sandstones, in deep diagenesis conditions similar to those of deeply buried reservoirs. These fault rocks are characterized by a foliated fabric and quartz-calcite sealed veins, which formation resulted from the combination of the (1) pressure solution of quartz, (2) intense fracturing sealed by quartz and calcite cements, and (3) neoformation of synkinematic white micas derived from the alteration of feldspars and chlorite. Fluid inclusion microthermometry in quartz and calcite cements demonstrates fault activity at temperatures of 195°C to 268°C. Permeability measurements on plugs oriented parallel with the principal axes of the finite strain ellipsoid show that the Y axis (parallel with the foliation and veins) is the direction of highest permeability in the foliated sandstone (10 -2 md for Y against 10 -3 md for X, Z, and the protolith, measured at a confining pressure of 20 bars). Microstructural observations document the localization of the preferential fluid path between the phyllosilicate particles forming the foliation. Hence, the direction of highest permeability in these fault rocks would be parallel with the fault and subhorizontal, that is, perpendicular to the slickenlines representing the local slip direction on the fault surface. We suggest

No abstract

Conventional triaxial tests were performed on a series of samples of Tournemire shale along different orientations relative to bedding (0°, 90°). Experiments were carried out up to failure at increasing confining pressures ranging from 2.5 to 80 MPa, and at strain rates ranging between 3 × 10−7 s−1 and 3 × 10−5 s−1. During each experiment, P and S wave elastic velocities were continuously measured along many raypaths with different orientations with respect to bedding and maximum compressive stress. This extensive velocity measurement setup allowed us to highlight the presence of plastic mechanisms such as mineral reorientation during deformation. The evolution of elastic anisotropy was quantified using Thomsen's parameters which were directly inverted from measurement of elastic wave velocity. Brittle failure was preceded by a change in P wave anisotropy, due to both crack growth and mineral reorientation. Anisotropy variations were largest for samples deformed perpendicular to bedding, at the onset of rupture. Anisotropy reversal was observed at the highest confining pressures. For samples deformed parallel to bedding, the P wave anisotropy change is weaker.

Calcite veins as an indicator of fracture dilatancy and connectivity during strike-slip faulting in Toarcian shale (Tournemire tunnel, Southern France) Author links open overlay panelMélodyLefèvre a YvesGuglielmi a PierreHenry a PierreDick b ClaudeGout c Show more https://doi.org/10.1016/j.jsg.2016.01.002 Get rights and content Highlights • Cathode-luminescence observations indicate that two phases of vein formation occurred. • Fluids circulations mainly off the shear surfaces in centimeter scale dilatant volumes. • Relationships between calcite concentration and strain partition around the fault main slip surface. AbstractThe reactivation of faults induced by natural/human induced fluid pressure increases is a major concern to explain subsurface fluid migration and to estimate the risk of losing the integrity of reservoir/seal systems. This study focusses on paleo-fluid migration in a strike slip fault with >100 m long, affecting a Toarcian shale (Causses Basin, France).A high calcite concentration is observed in a 5 cm thick zone at the boundary between the fault core and damage zone. Cumulated displacements in this zone are of millimeter-to-centimeter-scale offsets and different dilatant deformation textures are observed. The zone is affected by thin slip planes containing gouge. Cathodoluminescence observations indicate that two phases of vein formation occurred. The first phase coincides with the fluid migration along this centimeter thick dilatant zone.The second one is associated to re-shear along the millimeter thick slip planes that results in more localized mineralization, but also in a better hydrologic connection through the shale formation. These results show that in shales fluids may migrate off a slipping surface in centimeter scale dilatant volumes, at first controlled by the intact shale anisotropy related to bedding and then favored by brecciating, structures reorientation and strengthening processes induced by calcite sealing effects. 

No abstract