Ink-jet printed small-molecule organic single-crystal transistors are realized by using selective surface energy modification, precise control of volume density of ink droplets on spatially patterned areas, and a co-solvent system to control solvent evaporation properties. The single-crystal formation in bottom-contact-structured transistors via direct printing is expected to permit high-density array fabrication in large-area electronics.

Fast optical circuit switches (OCSs) with high port count offer reconfigurable bandwidth in optical networks and have the potential to significantly increase the performance and efficiency of modern datacenters. In this paper, we report on a new type of integrated OCS that combines silicon photonics with MEMS actuation. The switch is built on a 50 × 50 passive crossbar network with very low optical loss (0.04 dB/crossing). Efficient switching is achieved by a pair of directional couplers with moving waveguides and an actuation voltage of 14 V. 2500 MEMS-actuated directional coupler switches have been integrated with the crossbar network to form a strictly nonblocking 50 × 50 OCS on a 9 mm × 9 mm chip. The measured switching time is 2.5 μs, and the extinction ratio is 26 dB. To our knowledge, this is the largest silicon photonic switch reported to date. The switch architecture is highly scalable because the light travels through only one active switching element, regardless of the size of the switch.

The electrical characteristics of bottom-contact organic field-effect transistors fabricated with the air-stable n-type semiconductor N,N′-bis(n-octyl)-dicyanoperylene-3,4:9,10-bis(dicarboximide) (PDI-8CN2) are described. The mobility, threshold voltage, subthreshold swing, and Ion∕Ioff ratio(VDS=40V, VG=0∼40V) are 0.14cm2∕Vs, 1.6V, 2.0V/decade, and 1.2×103, respectively. The effect of electrode/dielectric surface treatment on these devices is also examined, with a combination of 1-octadecanethiol and hexamethyldisilazane. Organic complementary five-stage ring oscillators were fabricated using pentacene and PDI-8CN2, and operated at an oscillation frequency of 34kHz and a propagation delay per stage of 3μs.

Printed electronic circuits have been explored for low-cost, large-area applications, such as displays and radio frequency identification tags, where the promise of inexpensive solutionbased fabrication techniques is more crucial than the fast circuit speeds associated with conventional inorganic semiconductors. [1][2][3][4][5][6][7][8] In order for such low-cost, portable devices to become a reality, high-mobility, air-stable, n-channel organic field-effect transistors (OFETs) are required to enable the fabrication of organic complementary metal oxide semiconductor (CMOS) circuits that would operate at sufficient speeds and with low power dissipation. Additionally, the semiconductors must be solution processable to be compatible with the inexpensive fabrication techniques envisioned for printed electronics. Whereas most examples of printed organic semiconductors are conjugated p-type polymers, solution-processed OFETs with small molecules are far less common. [9,10] Previously, the small molecule semiconductor N,N′-bis(n-octyl)-(1,7&1,6)-dicyanoperylene-3,4:9,10-bis(dicar-boximide) (PDI-8CN 2 ) was used to fabricate promising vapordeposited n-channel OFETs with excellent electrical performance and remarkable environmental stability. [11,12] Because PDI-8CN 2 is soluble in common solvents such as chloroform, toluene, and dichlorobenzene, an intriguing question of whether it could be used for fabricating complex complementary organic circuits using solution-based processing techniques is raised. We report here the first fabrication of highperformance n-channel organic transistors and their complementary circuits from a PDI-8CN 2 solution with a micro-injector patterning technique. This work advances the pioneering results of Katz et al., [13] who fabricated a simple organic complementary inverter with a shadow-masked top-contact geometry. Unfortunately, such simple fabrication methods are not scalable for shrinking channel lengths to technologically useful sizes or for increasing the circuit complexity beyond inverter structures. These last two points represent the crossing of major technical hurdles in the development of organic complementary circuit technology. For the present OFET device fabrication, the organic semiconductor solutions were patterned in a nitrogen atmosphere using an Intracel Picospritzer, a pneumatically actuated micro-injector where droplet size is controlled by gas pressure and jetting time. The OFET gate dielectric and gold source/ drain electrode surfaces were treated with self-assembled monolayers (SAMs) to improve the surface energy match with the organic semiconductors and to produce approximately hemispherical solution droplets. Solvent selection proved crucial to the formation of uniform semiconductor films-for example, low-boiling solvents, such as chloroform, leave residue on the micropipette tip, adversely affecting the deposition process and the resultant film morphology. However, high-boiling solvents, such as 1,2-dichlorobenzene (bp 174°C) do not adversely affect the solution de...

No abstract

The 2016 EULAR/ACR/PRINTO classification criteria for MAS are potentially useful for the identification of patients with AOSD at high risk for a poor outcome. Febrile patients with AOSD should be monitored with the 2016 classification criteria for MAS in the early diagnosis and proper treatment of MAS.

We have developed a microelectromechanical system (MEMS) optical phased array incorporating a high-index-contrast subwavelength grating (HCG) for beamforming and beamsteering in a range of ± 1.26° × 1.26°. Our approach needs only a thin single-layer HCG made of silicon, considerably improving its speed thanks to the low mass, and is suitable for high optical power applications. The measured resonant frequency of HCG is 0.32 MHz.

No abstract