Because of its unprecedented theoretical capacity near 4000 mAh/g, which is approximately 10-fold larger compared to those of the current commercial graphite anodes, silicon has been the most promising anode for lithium ion batteries, particularly targeting large-scale energy storage applications including electrical vehicles and utility grids. Nevertheless, Si suffers from its short cycle life as well as the limitation for scalable electrode fabrication. Herein, we develop an electrospinning process to produce core-shell fiber electrodes using a dual nozzle in a scalable manner. In the core-shell fibers, commercially available nanoparticles in the core are wrapped by the carbon shell. The unique core-shell structure resolves various issues of Si anode operations, such as pulverization, vulnerable contacts between Si and carbon conductors, and an unstable sold-electrolyte interphase, thereby exhibiting outstanding cell performance: a gravimetric capacity as high as 1384 mAh/g, a 5 min discharging rate capability while retaining 721 mAh/g, and cycle life of 300 cycles with almost no capacity loss. The electrospun core-shell one-dimensional fibers suggest a new design principle for robust and scalable lithium battery electrodes suffering from volume expansion.
Layer-by-layer films comprised of alternating graphene and gold nanoparticle layers are readily produced by the two-step procedure involving the use of vacuum filtration of a reduced graphene oxide solution to fabricate the graphene thin film on the quartz substrate, followed by gold nanoparticle formation by spontaneous reduction of gold ions in a gold salt solution on the graphene films.
Homogeneous distribution of graphene flakes in a polymer matrix, still preserving intrinsic material properties, is key to successful composite applications. A novel approach is presented to disperse non-oxidized graphene flakes with non-covalent functionalization of 1-pyrenebutyric acid and to fabricate nanocomposites with outstanding thermal conductivity (∼1.53 W/mK) and mechanical properties (∼1.03 GPa).
The development of high-performance shielding materials against electromagnetic pollution requires mobile charge carriers and magnetic dipoles. Herein, we meet the challenge by building a three-dimensional (3D) nanostructure consisting of chemically modified graphene/Fe3O4(GF) incorporated polyaniline. Intercalated GF was synthesized by the in situ generation of Fe3O4 nanoparticles in a graphene oxide suspension followed by hydrazine reduction, and further in situ polymerization with aniline to form a polyaniline composite. Spectroscopic analysis demonstrates that the presence of GF hybrid structures facilitates strong polarization due to the formation of a solid-state charge-transfer complex between graphene and polyaniline. This provides proper impedance matching and higher dipole interaction, which leads to the high microwave absorption properties. The higher dielectric loss (ε'' = 30) and magnetic loss (μ'' = 0.2) contribute to the microwave absorption value of 26 dB (>99.7% attenuation), which was found to depend on the concentration of GF in the polyaniline matrix. Moreover, the interactions between Fe3O4, graphene and polyaniline are responsible for superior material characteristics, such as excellent environmental (chemical and thermal) degradation stability and good electric conductivity (as high as 260 S m(-1)).
A new method for the preparation of graphene has been developed via porphyrin exfoliation of graphite in NMP. The exfoliation, which follows the intercalation of organic ammonium ions, is based on the pi-pi interaction between graphene and porphyrins. The graphene sheets prepared by this method show undisturbed sp(2) carbon networks.
In this report, we describe the structure of a robust and highly conductive 3D graphene oxide hydrogel. The reduced graphene oxide hydrogel or rGH is fabricated by a crosslinking reaction with ethylene diamine followed by a hydrazine reduction. The material showed a high electrical conductivity of 1351 S m À1 and a specific surface area of 745 m 2 g À1 with 10.3 MPa break strength. When used as electrodes for a supercapacitor, it showed a high specific capacitance of 232 F g À1 .
Poly(3‐hexylthiophene) (P3HT) hybrids with single‐walled carbon nanotubes (SWNTs) were prepared using a series of SWNTs with various defect contents on their surfaces. The hybrids were synthesized by exploiting the π–π interaction between P3HT and the SWNTs, resulting in efficient dispersion of the carbon nanotubes in the P3HT solution. UV‐visible and photoluminescence (PL) spectra showed that the carbon nanotubes quench the PL of P3HT in the hybrids, indicating that electron transfer occurs from photo‐excited P3HT to the SWNTs. This electron transfer from P3HT to carbon nanotubes was disrupted by the presence of defects on the SWNT surfaces. However, the PL lifetime of P3HT in the hybrids was found to be the same as that of pure P3HT in solution, indicating the formation of a ground‐state non‐fluorescent complex of P3HT/SWNTs.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.