Hydrogen-terminated diamond surfaces can be covalently modified with molecules bearing a terminal vinyl (C=C) group via a photochemical process using sub-band-gap light at 254 nm. We have investigated the photochemical modification of hydrogen-terminated surfaces of nanocrystalline and single-crystal diamond (111) to help understand the structure of the films and the underlying mechanism of photochemical functionalization. A comparison of the rates of photochemical modification of single-crystal diamond and nanocrystalline diamond films shows no significant difference in reactivity, demonstrating that the modification process is not controlled by grain boundaries or other structures unique to polycrystalline films. We find that both single-crystal and polycrystalline hydrogen-terminated diamond samples exhibit negative electron affinity and are functionalized at comparable rates, while oxidized surfaces with positive electron affinity undergo no detectable reaction. Gas chromatography-mass spectrometry (GC-MS) analysis shows the formation of new chemical products in the liquid phase that are formed only when the alkenes are illuminated in direct contact with H-terminated diamond, while control experiments with other surfaces and in the dark show no reaction. Our results show that the functionalization is a surface-mediated photochemical reaction and suggest that modification is initiated by the photoejection of electrons from the diamond surfaces into the liquid phase.

Exposing single-walled carbon nanotubes to room-temperature UV-generated ozone leads to an irreversible increase in their electrical resistance. We demonstrate that the increased resistance is due to ozone oxidation on the sidewalls of the nanotubes rather than at the end caps. Raman and X-ray photoelectron spectroscopies show an increase in the defect density due to the oxidation of the nanotubes. Using ultraviolet photoelectron spectroscopy, we show that these defects represent the removal of pi-conjugated electron states near the Fermi level, leading to the observed increase in electrical resistance. Oxidation of carbon nanotubes is an important first step in many chemical functionalization processes. Because the oxidation rate can be controlled with short exposures, UV-generated ozone offers the potential for use as a low-thermal-budget processing tool.

We compare two different strategies for covalently modifying carbon nanofibers with biological molecules such as DNA. One method begins with a photochemical reaction between the nanofibers and molecules bearing both a terminal olefin group and a protected amine group followed by deprotection to yield the free primary amine. The second method uses a chemical reaction of an aryldiazonium salt with the nanofibers followed by electrochemical reduction to the primary amine. Both methods then link the primary amines to thio-terminated DNA oligonucleotides. Our measurements show that both methods yield DNA-modified carbon nanofibers exhibiting excellent specificity and reversibility in binding to DNA probe molecules in solution having complementary vs noncomplementary sequences. Quantitative measurements show that 2.3 × 10 14 DNA molecules/cm 2 will hybridize to the DNA-modified nanofiber samples, approximately eight times higher than for a flat sample of glassy carbon functionalized in an identical manner. Similar results were obtained comparing the amount of avidin that specifically binds to biotin-modified surfaces of nanofibers and glassy carbon. Our results demonstrate the ability to covalently functionalize nanofibers via two different methods that both provide excellent biomolecular recognition properties. Since the photochemical method uses molecules that are highly insulating while the diazonium method uses molecules bearing aromatic groups that are expected to be conductive, these methods can be used to prepare biologically modified nanofibers with a range of electrical properties that may be useful for electrical sensing of specific biomolecules in solution.

The interaction of proteins with semiconductors such as silicon and diamond is of great interest for applications such as electronic biosensing. We have investigated the use of covalently bound oligo(ethylene glycol), EG, monolayers on diamond and silicon to minimize nonspecific protein adsorption. Protein adsorption was monitored by fluorescence scanning as a function of the length of the ethylene glycol chain (EG3 through EG6) and the terminal functional group (methyl- versus hydroxyl-terminated EG3 monolayer). More quantitative measurements were made by eluting adsorbed avidin from the surface and measuring the intensity of fluorescence in the solution. The attachment chemistry of the tri(ethylene glycol) molecules and monolayer orientation was studied by X-ray photoelectron spectroscopy. Improvement in the selectivity of surfaces modified with EG functionality was demonstrated in two model biosensing assays. We find that high-quality EG monolayers are formed on silicon and diamond and that these EG3 monolayers are as effective as EG3 self-assembled monolayers on gold at resisting nonspecific avidin adsorption. These results show promise for use of silicon and diamond materials in many potential applications such as biosensing and medical implants.