No abstract

Electric vehicles (EVs) are spreading rapidly and many counties are promoting hybrid and fully EVs through legislation. Therefore, an increasing amount of lithium ion batteries will reach the end of their usable life and will require effective and sustainable end-of-life management plan which include landfill disposal or incineration. The current research focuses on more sustainable methods such as remanufacturing, reuse and recycling in order to prepare for future battery compositions and provide insights to the need recycling methods to be developed to handle large amounts of batteries sustainably in the near future. The two most prominent material recovery techniques are hydrometallurgy and pyrometallurgy which are explored and assessed on their relative effectiveness, sustainability, and feasibility. Hydrometallurgy is a superior recycling method due to high material recovery and purity, very low emissions, high prevalence of chemical reuse and implementation of environmentally sustainable compounds. Expanding recycling technologies globally should take the research and technologies pioneered by Umicore to establish a sustainable recycling program for end-of-life EVs batteries. Emerging battery technology of Telsa show the most effective designs for high performance batteries includes the use of silicon which is expected to increase capacity of batteries in the future.

No abstract

The quality of compost made from dewatered sewage sludge, sawdust (SD) and organic wastes of a potato-processing industry (OW), in terms of chemical and biological properties, was assessed. Mixtures of the sludge, SD and OW were composted for 57 days in insulated containers at two C:N ratios (approximately 30 : 1 and approximately 20 : 1) and SD textures (coarse- and fine-textured SD). The parameters monitored over this period were pH, electrical conductivity (EC), C:N ratio, CO2 evolution and two spectrophotometric ratios (Q2/6 and Q2/4). All the studied parameters were in general similarly influenced by initial C:N ratio and texture of SD except for EC, Q2/6 and Q2/4. At high C:N ratio of both textures, the EC of the final products increased but were less than those of low C:N ratio of both textures. Thus, final product can be used alone as growth medium without the need for grinding or blending with other materials. The spectrophotometric ratios (Q2/6 and Q2/4) dramatically decreased two weeks after composting and then slightly increased at the end of composting process. However, coarse-textured SD at the low C:N ratio and fine-textured SD at both C:N ratios resulted in lower Q2/6 and Q2/4 ratios, reflecting a better degree of aromatic condensation and organic matter humification. Considering these parameters, co-composting sludge with fine-textured SD and OW at high initial C:N ratio would represent the best compromise.

This research documents two innovative designs of septic tanks used for onsite wastewater treatment. The designs were implemented and tested as part of a research project focused on innovative decentralized wastewater treatment solutions. The modified septic tanks were tested at different hydraulic loading rates for sufficient periods to effectively evaluate their performance. The two systems were designed with successive anaerobic and aerobic chambers and were differentiated between attached and suspended growth. The systems were operated at detention times of 4.3, 3.2, and 2.6 days. High removal of organic load was achieved under all loading criteria in both systems. Effluent BOD 5 concentration at lower and higher loading rates were found to be less than 15 and 25 mg/L, respectively, representing a removal rate of more than 95%. Nitrogen was also removed but at a lower rate. The highest TN removal was achieved (59%) in the attached growth system at the lowest loading rate. Although two logs of E. coli removal (99%) were achieved in all systems, E. coli numbers were high enough to necessitate further tertiary treatment. The modified septic tanks proved to be a cost-effective technology with low energy and O&M requirements.

No abstract

The article examines the impact differences between producing concrete and asphalt. Both materials are widely used in the construction industry. Construction activities account for a large portion of greenhouse gases. Therefore, it is important to consider the Life Cycle Analysis (LCA) to reduce environmental impacts. In this study, the material processes were inputted into an LCA program called SimaPro. The database used for the study was Ecoinvent as it is one of the major databases within SimaPro. The materials were compared against impacts per kg of material produced as the functional unit. Each process was created using the materials, energy and transportation required to produce the materials. Waste streams were also included in the process to determine the impacts after the product was done with its useful life. Using the ReCiPe method, an LCA was conducted. Midpoint and endpoint categories were examined for both the productions. The processes had similar results for the human health and ecosystems categories; however asphalt was marginally higher for both. Asphalt had exceeded concrete in the resource impact category by 100 mPt. The results indicate that concrete is the more sustainable building material. Determination of various impacts of the materials is important for material selection.

The bioremediation of petroleum contaminated soil was investigated using a laboratory scale aerated reactor. The Indigenous bacteria, Stenotrophomonas multophilia, were isolated from the contaminated sites near to Jordan Petroleum Refinery and used further in the bioremediation experiments. First order kinetic equation has been proven to satisfactorily describe the biodegradation of petroleum contained in soil in the presence of the isolated bacteria. The results also showed that the first order kinetic constants for the different bioreactors vary between 0.041 and 0.0071/ day. The overall kinetic constant k′ was determined based on food-to-microorganisms ratio and found to be 0.02/day.