A series of spray-flame made LaCo1−xFexO3 nanoparticles showed promising activity for liquid-phase cyclohexene oxidation. Various oxidizing agents, i.e., O2, H2O2 and tert-butyl hydroperoxide, led to different product selectivities.
Noble‐metal‐free perovskite oxides are promising and well‐known catalysts for high‐temperature gas‐phase oxidation reactions, but their application in selective oxidation reactions in the liquid phase has rarely been studied. We report the liquid‐phase oxidation of cinnamyl alcohol over spray‐flame synthesized LaCo1–xFexO3 perovskite nanoparticles with tert‐butyl hydroperoxide (TBHP) as the oxidizing agent under mild reaction conditions. The catalysts were characterized by XRD, BET, EDS and elemental analysis. LaCo0.8Fe0.2O3 showed the best catalytic properties indicating a synergistic effect between cobalt and iron. The catalysts were found to be stable against metal leaching as proven by hot filtration, and the observed slight deactivation is presumably due to segregation as determined by EDS. Kinetic studies revealed an apparent activation energy of 63.6 kJ mol−1. Combining kinetic findings with TBHP decomposition as well as control experiments revealed a complex reaction network.
Coupling electrochemical generation of hydrogen with the concomitant formation of an industrially valuable product at the anode instead of oxygen can balance the high costs usually associated with water electrolysis. We report the synthesis of a variety of nanoparticulate LaCo1−xFexO3 perovskite materials through a specifically optimized spray‐flame nanoparticle synthesis method, using different ratios of La, Co, and Fe precursor compounds. Structural characterization of the resulting materials by XRD, TEM, FTIR, and XPS analysis revealed the formation of mainly perovskite‐type materials. The electrocatalytic performance of the formed perovskite‐type materials towards the oxygen evolution reaction and the ethanol oxidation reaction was investigated by using rotating disk electrode voltammetry. An increased Fe content in the precursor mixture leads to a decrease in the electrocatalytic activity of the nanoparticles. The selectivity towards alcohol oxidation in alkaline media was assessed by using the ethanol oxidation reaction as a model reaction. Operando electrochemistry/ATR‐IR spectroscopy results reveal that acetate and acetaldehyde are the final products, depending on the catalyst composition as well as on the applied potential.
The product properties of mixed oxide nanoparticles generated via spray-flame synthesis depend on an intricate interplay of solvent and precursor chemistries in the processed solution. The effect of two different sets of metal precursors, acetates and nitrates, dissolved in a mixture of ethanol (35 Vol.%) and 2-ethylhexanoic acid (2-EHA, 65 Vol.%) was investigated for the synthesis of LaFe x Co 1−x O 3 (x = 0.2, 0.3) perovskites. Regardless of the set of precursors, similar particle-size distributions (d p = 8− 11 nm) were obtained and a few particles with sizes above 20 nm were identified with transmission electron microscopy (TEM) measurements. Using acetates as precursors, inhomogeneous La, Fe, and Co elemental distributions were obtained for all particle sizes according to energy dispersive X-ray (EDX) mappings, connected to the formation of multiple secondary phases such as oxygen-deficient La 3 (Fe x Co 1−x ) 3 O 8 brownmillerite or La 4 (Fe x Co 1−x ) 3 O 10 Ruddlesden−Popper (RP) structures besides the main trigonal perovskite phase. For samples synthesized from nitrates, inhomogeneous elemental distributions were observed for large particles only where La and Fe enrichment occurred in combination with the formation of a secondary La 2 (Fe x Co 1−x )O 4 RP phase. Such variations can be attributed to reactions in the solution prior to injection in the flame as well as precursor-dependent variations in in-flame reactions. Therefore, the precursor solutions were analyzed by temperature-dependent attenuated total reflection Fouriertransform infrared (ATR-FTIR) measurements. The acetate-based precursor solutions indicated the partial conversion of, mainly La and Fe, acetates to metal 2-ethylhexanoates. In the nitrate-based solutions, esterification of ethanol and 2-EHA played the most important role. The synthesized nanoparticle samples were characterized by BET (Brunauer, Emmett, Teller), FTIR, Mossbauer, and X-ray photoelectron spectroscopy (XPS). All samples were tested as oxygen evolution reaction (OER) catalysts, and similar electrocatalytic activities were recorded when evaluating the potential required to reach 10 mA/cm 2 current density (∼1.61 V vs reversible hydrogen electrode (RHE)).
La1−xSrxCoO3 (x=0, 0.1, 0.2, 0.3, 0.4) nanoparticles were prepared by spray‐flame synthesis and applied in the liquid‐phase oxidation of cyclohexene with molecular O2 as oxidant under mild conditions. The catalysts were systematically characterized by state‐of‐the‐art techniques. With increasing Sr content, the concentration of surface oxygen vacancy defects increases, which is beneficial for cyclohexene oxidation, but the surface concentration of less active Co2+ was also increased. However, Co2+ cations have a superior activity towards peroxide decomposition, which also plays an important role in cyclohexene oxidation. A Sr doping of 20 at. % was found to be the optimum in terms of activity and product selectivity. The catalyst also showed excellent reusability over three catalytic runs; this can be attributed to its highly stable particle size and morphology. Kinetic investigations revealed first‐order reaction kinetics for temperatures between 60 and 100 °C and an apparent activation energy of 68 kJ mol−1 for cyclohexene oxidation. Moreover, the reaction was not affected by the applied O2 pressure in the range from 10 to 20 bar. In situ attenuated total reflection infrared spectroscopy was used to monitor the conversion of cyclohexene and the formation of reaction products including the key intermediate cyclohex‐2‐ene‐1‐hydroperoxide; spin trap electron paramagnetic resonance spectroscopy provided strong evidence for a radical reaction pathway by identifying the cyclohexenyl alkoxyl radical.
Spray‐flame synthesis was used to produce high‐surface‐area perovskite electrocatalysts with high phase purity, minimum surface contamination, and high electrochemical stability. In this study, as‐prepared LaCo1–xFexO3 perovskite nanoparticles (x=0.2, 0.3, and 0.4) were found to contain a high degree of combustion residuals, and mostly consist of both, stoichiometric and oxygen‐deficient perovskite phases. Heating them at moderate temperature (250 °C) in oxygen could remove combustion residuals and increases the content of stoichiometric perovskite while preventing particle growth. A higher surface crystallinity was observed with increasing iron content coming along with a rise in oxygen deficient phases. With heat treatment, OER activity and stability of perovskites improved at 30 and 40 at.% Fe while deteriorating at 20 at.% Fe. This study highlights spray‐flame synthesis as a promising technique to synthesize highly active nanoscale perovskite catalysts with improved OER activity.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.