The effect of surface roughness on osteoblast proliferation, differentiation, and protein synthesis was examined. Human osteoblast-like cells (MG63) were cultured on titanium (Ti) disks that had been prepared by one of five different treatment regimens. All disks were pretreated with hydrofluroic acid-nitric acid and washed (PT). PT disks were also: washed, and then electropolished (EP); fine sandblasted, etched with HCl and H2SO4, and washed (FA); coarse sandblasted, etched with HCl and H2SO4, and washed (CA); or Ti plasma-sprayed (TPS). Standard tissue culture plastic was used as a control. Surface topography and profile were evaluated by brightfield and darkfield microscopy, cold field emission scanning electron microscopy, and laser confocal microscopy, while chemical composition was mapped using energy dispersion X-ray analysis and elemental distribution determined using Auger electron spectroscopy. The effect of surface roughness on the cells was evaluated by measuring cell number, [3H]thymidine incorporation into DNA, alkaline phosphatase specific activity, [3H]uridine incorporation into RNA, [3H]proline incorporation into collagenase digestible protein (CDP) and noncollagenase-digestible protein (NCP), and [35S]sulfate incorporation into proteoglycan. Based on surface analysis, the five different Ti surfaces were ranked in order of smoothest to roughest: EP, PT, FA, CA, and TPS. A TiO2 layer was found on all surfaces that ranged in thickness from 100 A in the smoothest group to 300 A in the roughest. When compared to confluent cultures of cells on plastic, the number of cells was reduced on the TPS surfaces and increased on the EP surfaces, while the number of cells on the other surfaces was equivalent to plastic. [3H]Thymidine incorporation was inversely related to surface roughness. Alkaline phosphatase specific activity in isolated cells was found to decrease with increasing surface roughness, except for those cells cultured on CA. In contrast, enzyme activity in the cell layer was only decreased in cultures grown on FA- and TPS-treated surfaces. A direct correlation between surface roughness and RNA and CDP production was found. Surface roughness had no apparent effect on NCP production. Proteoglycan synthesis by the cells was inhibited on all the surfaces studied, with the largest inhibition observed in the CA and EP groups. These results demonstrate that surface roughness alters osteoblast proliferation, differentiation, and matrix production in vitro. The results also suggest that implant surface roughness may play a role in determining phenotypic expression of cells in vivo.

Titanium (Ti) is used for implantable devices because of its biocompatible oxide surface layer. TiO2 surfaces that have a complex microtopography increase bone-to-implant contact and removal torque forces in vivo and induce osteoblast differentiation in vitro. Studies examining osteoblast response to controlled surface chemistries indicate that hydrophilic surfaces are osteogenic, but TiO2 surfaces produced until now exhibit low surface energy because of adsorbed hydrocarbons and carbonates from the ambient atmosphere or roughness induced hydrophobicity. Novel hydroxylated/hydrated Ti surfaces were used to retain high surface energy of TiO2. Osteoblasts grown on this modified surface exhibited a more differentiated phenotype characterized by increased alkaline phosphatase activity and osteocalcin and generated an osteogenic microenvironment through higher production of PGE2 and TGF-beta1. Moreover, 1alpha,25OH2D3 increased these effects in a manner that was synergistic with high surface energy. This suggests that increased bone formation observed on modified Ti surfaces in vivo is due in part to stimulatory effects of high surface energy on osteoblasts.

No abstract

Titanium (Ti) osseointegration is critical for the success of dental and orthopaedic implants. Previous studies have shown that surface roughness at the micro- and submicro-scales promotes osseointegration by enhancing osteoblast differentiation and local factor production. Only relatively recently have the effects of nanoscale roughness on cell response been considered. The aim of the present study was to develop a simple and scalable surface modification treatment that introduces nanoscale features to the surfaces of Ti substrates without greatly affecting other surface features, and to determine the effects of such superimposed nano-features on the differentiation and local factor production of osteoblasts. A simple oxidation treatment was developed for generating controlled nanoscale topographies on Ti surfaces, while retaining the starting micro-/submicro-scale roughness. Such nano-modified surfaces also possessed similar elemental compositions, and exhibited similar contact angles, as the original surfaces, but possessed a different surface crystal structure. MG63 cells were seeded on machined (PT), nano-modified PT (NMPT), sandblasted/acid-etched (SLA), and nano-modified SLA (NMSLA) Ti disks. The results suggested that the introduction of such nanoscale structures in combination with micro-/submicro-scale roughness improves osteoblast differentiation and local factor production, which, in turn, indicates the potential for improved implant osseointegration in vivo.

Polyvinyl alcohol (PVA) is a synthetic polymer derived from polyvinyl acetate through partial or full hydroxylation. PVA is commonly used in medical devices due to its low protein adsorption characteristics, biocompatibility, high water solubility, and chemical resistance. Some of the most common medical uses of PVA are in soft contact lenses, eye drops, embolization particles, tissue adhesion barriers, and as artificial cartilage and meniscus. The purpose of this review is to evaluate the available published information on PVA with respect to its safety as a medical device implant material for cartilage replacement. The review includes historical clinical use of PVA in orthopedics, and in vitro and in vivo biocompatibility studies. Finally, the safety recommendation involving the further development of PVA cryogels for cartilage replacement is addressed.

Dental and orthopaedic implants have been under continuous advancement to improve their interactions with bone and ensure a successful outcome for patients. Surface characteristics such as surface topography and surface chemistry can serve as design tools to enhance the biological response around the implant, with in vitro, in vivo and clinical studies confirming their effects. However, the comprehensive design of implants to promote early and long-term osseointegration requires a better understanding of the role of surface wettability and the mechanisms by which it affects the surrounding biological environment. This review provides a general overview of the available information about the contact angle values of experimental and of marketed implant surfaces, some of the techniques used to modify surface wettability of implants, and results from in vitro and clinical studies. We aim to expand the current understanding on the role of wettability of metallic implants at their interface with blood and the biological milieu, as well as with bacteria, and hard and soft tissues.

Biomaterial surface properties including chemistry, topography, and wettability regulate cell response. Previous studies have shown that increasing surface roughness of metallic orthopaedic and dental implants improved bone formation around the implant. Little is known about how implant surface properties can affect immune cells that generate a wound healing microenvironment. The aim of our study was to examine the effect of surface modifications on macrophage activation and cytokine production. Macrophages were cultured on seven surfaces: tissue culture polystyrene (TCPS) control; hydrophobic and hydrophilic smooth Ti (PT and oxygen-plasma-treated (plasma) PT); hydrophobic and hydrophilic microrough Ti (SLA and plasma SLA), and hydrophobic and hydrophilic nano-and micro-rough Ti (aged modSLA and modSLA). Smooth Ti induced inflammatory macrophage (M1-like) activation, as indicated by increased levels of interleukins IL-1β, IL-6, and TNFα. In contrast, hydrophilic rough titanium induced macrophage activation similar to the anti-inflammatory M2-like state, increasing levels of interleukins IL-4 and IL-10. These results demonstrate that macrophages cultured on high surface wettability materials produce an anti-inflammatory microenvironment, and this property may be used to improve the healing response to biomaterials.

Titanium (Ti) surface roughness affects proliferation, differentiation, and matrix production of MG-63 osteoblast-like cells. Cytokines and growth factors produced in the milieu surrounding an implant may also be influenced by its surface, thereby modulating the healing process. This study examined the effect of surface roughness on the production of two factors known to have potent effects on bone, prostaglandin E2 (PGE2) and transforming growth factor beta 1 (TGF-beta 1). MG-63 cells were cultured on Ti disks of varying roughness. The surfaces were ranked from smoothest to roughest: electropolished (EP), pretreated with hydrofluoric acid-nitric acid (PT), fine sand-blasted, etched with HCl and H2SO4, and washed (EA), coarse sand-blasted, etched with HCl and H2SO4, and washed (CA), and Ti plasma-sprayed (TPS). Cells were cultured in 24-well polystyrene (plastic) dishes as controls and to determine when confluence was achieved. Media were collected and cell number determined 24 h postconfluence. PGE2 and TGF-beta 1 levels in the conditioned media were determined using commercial radioimmunoassay and enzyme-linked immunosorbent assay kits, respectively. There was an inverse relationship between cell number and Ti surface roughness. Total PGE2 content in the media of cultures grown on the three roughest surfaces (FA, CA, and TPS) was significantly increased 1.5-4.0 times over that found in media of cultures grown on plastic or smooth surfaces. When PGE2 production was expressed per cell number, CA and TPS cultures exhibited six- to eightfold increases compared to cultures on plastic and smooth surfaces. There was a direct relationship between TGF-beta 1 production and surface roughness, both in terms of total TGF-beta 1 per culture and when normalized for cell number. TGF-beta 1 production on rough surfaces (CA and TPS) was three to five times higher than on plastic. These studies indicate that substrate surface roughness affects cytokine and growth factor production by MG-63 cells, suggesting that surface roughness may modulate the activity of cells interacting with an implant, and thereby affect tissue healing and implant success.