Purpose The purpose of this paper is to present the methodology for manufacturing of aircraft transmission gears using incremental method of rapid prototyping (RP) – direct metal laser sintering (DMLS). The production of prototypes from metallic powders using described system allows the execution of final elements of complex structures with additional economic impacts. Design/methodology/approach The paper describes the use of selective laser sintering method (DMLS) by EOS Company. Whole chain of production of prototype is presented with the addition of geometric accuracy measurements by blue light laser device. Findings Presented in the research analysis of SLS/SLM technologies as rapid manufacturing systems shows that they can be applied in the production of prototypes used in the manufacturing process of gears for propulsion systems in aviation industry. Also, very important is the geometrical accuracy of gear prototypes produced by incremental methods. It determines subsequent treatment steps for aircraft propulsion system gears. Practical Implications The use of RP techniques as an alternative for conventionally used manufacturing method has mainly an economic impact related to the cost of time-consuming process and amount of defected elements appearing in serial production. Originality/value This paper presents possibility to use RP – DMLS system – for propulsion elements of aircraft structure. This research is original because of the complex description of the whole chain of manufacturing process. Additionally, geometrical accuracy measurement methodology by blue light presented with the RP method of manufacturing gives the research a unique characteristic.
Purpose The purpose of this paper is to present coordinate measuring system possibilities in the meaning of the geometric accuracy assessment of hot zone elements in aircraft engines. The aim of the paper is to prove that this method, which uses blue light and is most sufficient and cost-saving method, can to be used in the production line for serial manufacturing of elements, for which a high level of accuracy is required. Design/methodology/approach The analysis of the geometric accuracy of the blades was performed using non-contact optical coordinate scanner ATOS Triple Scan II Blue Light, manufactured by GOM Company, at the Department of Mechanical Engineering, Rzeszów University of Technology. Geometric analysis was conducted for blades manufactured from different waxes (A7Fr/60 and RealWax VisiJet CPX200), thus comparing injection technique and rapid prototyping (RP) method, and for casting made of Inconel 713C nickel-based superalloy. Findings The analysis of the criteria for the method of blades’ measuring selection showed that the chosen system successfully met all criteria for the verification of blades’ geometry at the selected stages of the process. ATOS II optical scanner with blue light technology allows measurement almost regardless of daylight or artificial (white) light. This allows the application of the measurement system in the production cycle, thus eliminating the need to create special conditions for measurements. Practical implications Requirements related to the accuracy of measured values, diversity and allowable measurement time are linked with the methods of production. Modern manufacturing methods based on computer-aided design systems/manufacturing/engineering systems require a non-contact optical measurement method based on the computer-aided-based coordinate measuring technique. In case of the non-contact optical scanning method based on the ATOS GOM measuring system, time and measurement costs depend on the methodology of measurement and the possibility of its automation. This is why the presented paper has a practical impact on possibilities for the automation of geometric accuracy measurements of obtained elements in the series production line. Social implications The use of ATOS Triple Scan II Blue Light by GOM Company allows the reduction of cost and time of production because of the possibility of the introduction of this system in an automated production line. Additionally, the measurement of hot section blades of aircraft engines by using the blue light method is much more accurate and has implication as it impacts safety of further used manufactured elements. Originality/value This paper presents the possibility of using the ATOS Triple Scan II Blue Light measuring system for geometric accuracy measurements in case of hot section blades of aircraft engines. This research is original because it describes three model geometric accuracy measurements, wax model obtained using the injection technique, wax model obtained using the I RP process and casting made of Inco...
The article presents the results of strength tests in the form of a static tensile test on the INSTRON 5967 testing machine. Samples were made with the use of the Prusa i3 MK3 3D printer, by modeling with a plasticized material (FFF) made of ABS copolymer, polylactide and its modified variant. According to the information provided by the manufacturer, heat-treated modified polylactide has mechanical properties similar to ABS copolymer filament. The publication also discusses the method of manufacturing elements subjected to the tests, the heat treatment process, as well as changes in material properties as a result of this treatment. Based on the test results, it was found that the annealing process increased the proportion of the crystalline phase, which significantly improved the strength properties of the modified polylactide.
Purpose – The analysis, carried out for this publication, concerned checking the nature of mating of gear wheels with different load conditions. The computation was made applying FEM in Abaqus 6.10-1 program and concerned spur gears in dual-power-path gears made of ABS. The same geometrical models, material parameters and boundary conditions were assumed for all the analysed stages of the computation. However, the values of torque transmitted from active wheels to passive wheel of the gearing were changed. The paper aims to discuss these issues. Design/methodology/approach – Observing changes of stress levels for toothed wheel and pinions allows to state that for relatively low load values, bending stresses at tooth root change proportionally to the change of the applied load. Findings – Values of contact stresses on mating teeth flanks were also defined for the most loaded part of the dual-power-path gearing, namely for a pinion. In case of contact stresses, it was observed that together with constant increase of torque value, the values of stresses change but the nature of these changes is not proportional to the applied load. Out of all the analysed variants, the most favourable, from the point of view of durability, was the situation in initial (theoretical) model with regular power division on all mating wheels. Originality/value – Conclusions drawn as a result of numerical computation are helpful in defining the nature of work of dual-power-path gearing in different load conditions and will be compared to results of stand tests of the analysed gearing.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.