No abstract

The improvement in low cycle fatigue life created by shot peening ferritic heat resistant steel was investigated in components of varying geometries based on those found in conventional power station steam turbine blades. It was found that the shape of the component did not affect the efficacy of the shot peening process, which was found to be beneficial even under the high stress amplitude three point bend loads applied. Furthermore, by varying the shot peening process parameters and considering fatigue life it has been shown that the three surface effects of shot peening; roughening, strain hardening and the generation of a compressive residual stress field must be included in remnant life models as physically separate entities. The compressive residual stress field during plane bending low cycle fatigue has been experimentally determined using X-ray diffraction at varying life fractions and found to be retained in a direction parallel to that of loading and to only relax to 80% of its original magnitude in a direction orthogonal to loading. This result, which contributes to the retention of fatigue life improvement in low cycle fatigue conditions, has been discussed in light of the specific stress distribution applied to the components. The ultimate aim of the research is to apply these results in a life assessment methodology which can be used to justify a reduction in the length of scheduled plant overhauls. This will result in significant cost savings for the generating utility. KeywordsLow cycle fatigue, stress concentration, shot peening, residual stresses, ferritic heat resisting

Abstract:In this study, short fatigue crack initiation and early growth behaviour under low cycle fatigue conditions was investigated in a shot peened low pressure steam turbine blade material. Four different surface conditions of notched samples have been considered: polished, ground, T0 (industry applied shot peened process) and T1 (a less intense shot peened process). Fatigue crack aspect ratio (a/c) evolution in the early stages of crack growth in polished and shot peened cases was found to be quite different: the former was more microstructure dependent (e.g. stringer initiation) while the crack morphology in the shot peened cases was more related to the shot peening process (i.e. surface roughness, position with respect to the compressive stress and strain hardening profiles). Under similar strain range conditions, the beneficial effect of shot peening (in the T0 condition) was retained even at a high strain level (Δε 11 =0.68%), N f, ground < N f, T1 < N f, polished < N f, T0 . The a/c evolution effects were incorporated in K-evaluations and used in calculating da/dN from surface replica data. Apparent residual stress (based on crack driving force ΔK difference) was applied to describe the benefit of shot peening and was seen to extend significantly below the measured residual stress profile, indicating the importance of the strain hardening layer and stress redistribution effects during crack growth.2

Fatigue initiation behaviour in three multi-component Al-Si casting alloys with varying Si content is compared using a range of microscopy and analytical techniques. A higher proportion of stiffer secondary phases leads to load transfer effects reducing particle cracking and particle/matrix debonding. Si appears stronger than the Al9FeNi phase, which cracks and debonds to form initiation sites preferentially over Si. Reducing Si content results in clusters of intermetallics forming, and increased porosity. The effect of porosity, combined with mesoscopic load transfer effects to the high volume fraction intermetallic regions make these potent crack initiation sites in low silicon alloys.

The limitations of 2-dimensional electrodes can be overcome by using threedimensional materials having sufficient porosity and active area while offering moderate mass transport rates and a relatively low pressure drop at controlled electrolyte flow rate. In concept, a wide variety of metal, ceramic and composite materials are possible but restrictions are imposed by the need to avoid materials degradation, while maintaining adequate electrical conductivity, sufficient robustness and the possibility of facile scale-up. Despite its fragility, one of the traditional electrode materials used as a porous, 3-dimensional electrode is carbon foam, particularly in the 97% vol. porous form of reticulated vitreous carbon, RVC. A timeline indicates that the history of this material dates back over 50 years to the mid1960s, when it was primarily used as an uncoated material in small-scale, laboratory electroanalysis. Surface modification and diverse coatings have considerably extended the use of RVC. Recent applications are found in sensors and monitors, electrosynthesis, environmental processing and energy conversion. This review highlights the fundamental structure and summarises the physicochemical properties of RVC. Fluid flow through various porosity grades of the material, their active electrochemical area and rates of mass transport are quantified. The diverse applications of RVC in energy conversion, environmental treatment and electrosynthesis are illustrated by selected examples from the authors' laboratories and others over the last 30 years. Recent research on coated RVC, energy conversion environmental remediation and sensors is highlighted. Critical areas deserving further research and development are proposed.