There is an urgent quest for room-temperature qubits in nanometer-sized, ultrasmall nanocrystals for quantum biosensing, hyperpolarization of biomolecules, and quantum information processing. Thus far, the preparation of such qubits at the nanoscale has remained futile. Here, we present a synthesis method that avoids any interaction of the solid with high-energy particles and uses self-propagated high-temperature synthesis with a subsequent electrochemical method, the no-photon exciton generation chemistry to produce room-temperature qubits in ultrasmall nanocrystals of sizes down to 3 nm with high yield. We first create the host silicon carbide (SiC) crystallites by high-temperature synthesis and then apply wet chemical etching, which results in ultrasmall SiC nanocrystals and facilitates the creation of thermally stable defect qubits in the material. We demonstrate room-temperature optically detected magnetic resonance signal of divacancy qubits with 3.5% contrast from these nanoparticles with emission wavelengths falling in the second biological window (1000− 1380 nm). These results constitute the formation of nonperturbative bioagents for quantum sensing and efficient hyperpolarization.

We present a novel method to determine the resonant frequency and quality factor of microwave resonators which is faster, more stable, and conceptually simpler than the yet existing techniques. The microwave resonator is irradiated at a frequency away from its resonance. It then emits an exponentially decaying radiation at its eigen-frequency when the excitation is rapidly switched off. The emission is down-converted with a microwave mixer, digitized and its Fourier transformation (FT) directly yields the resonance curve in a single shot. Being an FT based method, this technique possesses the Fellgett (multiplex) and Connes (accuracy) advantages and it conceptually mimics that of pulsed nuclear magnetic resonance. We also establish a novel benchmark to compare accuracy of the different approaches of microwave resonator measurements. This shows that the present method have similar accuracy to the existing ones.

No abstract

An efficient route to synthesize macroscopic amounts of graphene is highly desired and bulk characterization of such samples, in terms of the number of layers, is equally important. We present a Raman spectroscopy-based method to determine the typical upper limit of the number of graphene layers in chemically exfoliated graphene. We utilize a controlled vapour-phase potassium intercalation technique and identify a lightly doped stage, where the Raman modes of undoped and doped few-layer graphene flakes coexist. The spectra can be unambiguously distinguished from alkali doped graphite, and modeling with the typical upper limit of the layers yields an upper limit of flake thickness of five layers with a significant single-layer graphene content. Complementary statistical AFM measurements on individual few-layer graphene flakes find a consistent distribution of the layer numbers.

Black phosphorus (bP) has emerged as the next member in the graphene inspired two‐dimensional materials family. Its electronic and magnetic properties are studied herein using electron and nuclear magnetic resonance techniques (ESR and NMR) and microwave conductivity measurement. The latter is a unique technique to study conductivity on air sensitive samples. The ESR study indicates the absence of free charge carriers and no sign of paramagnetic defects are found. 31P NMR shows the presence of a characteristic Pake doublet structure due to the interaction between I = 1/2 nuclei. Microwave conductivity shows, in accordance with the ESR results, that black phosphorus behaves as a semiconductor and we identify extrinsic and intrinsic charge carrier contributions to the conductivity and extracted the sizes of the gaps. ESR measurement also yields that bP might find applications as a microwave absorbent.

Abstractauthoren We study the vibrational, magnetic and transport properties of Few Layer Graphene (FLG) using Raman and electron spin resonance spectroscopy and microwave conductivity measurements. FLG samples were produced using wet chemical exfoliation with different post‐processing, namely ultrasound treatment, shear mixing, and magnetic stirring. Raman spectroscopy shows a low intensity D mode which attests a high sample quality. The G mode is present at 1580 cm−1 as expected for graphene. The 2D mode consists of 2 components with varying intensities among the different samples. This is assigned to the presence of single and few layer graphene in the samples. Electron Spin Resonance (ESR) spectroscopy shows a main line in all types of materials with a width of about 1 mT and a g‐factor in the range of 2.005−2.010. Paramagnetic defect centers with a uniaxial g‐factor anisotropy are identified, which shows that these are related to the local sp2 bonds of the material. All kinds of investigated FLGs have a temperature dependent resistance which is compatible with a small gap semiconductor. The difference in resistance is related to the different grain size of the samples.

X-ray-activated near-infrared luminescent nanoparticles are considered as new alternative optical probes due to being free of autofluorescence, while both their excitation and emission possess a high penetration efficacy in vivo . Herein, we report silicon carbide quantum dot sensitization of trivalent chromium-doped zinc gallate nanoparticles with enhanced near-infrared emission upon X-ray and UV–vis light excitation. We have found that a ZnGa 2 O 4 shell is formed around the SiC nanoparticles during seeded hydrothermal growth, and SiC increases the emission efficiency up to 1 order of magnitude due to band alignment that channels the excited electrons to the chromium ion.

Nanomagnetic hyperthermia (NMH) is intensively studied with the prospect of cancer therapy. A major challenge is to determine the dissipated power during in vivo conditions and conventional methods are either invasive or inaccurate. We present a non-calorimetric method which yields the heat absorbed during hyperthermia: it is based on accurately measuring the quality factor change of a resonant radio frequency circuit which is employed for the irradiation. The approach provides the absorbed power in real-time, without the need to monitor the sample temperature as a function of time. As such, it is free from the problems caused by the non-adiabatic heating conditions of the usual calorimetry. We validate the method by comparing the dissipated power with a conventional calorimetric measurement. We present the validation for two types of resonators with very different filling factors: a solenoid and a so-called birdcage coil. The latter is a volume coil, which is generally used in magnetic resonance imaging (MRI) under in vivo condition. The presented method therefore allows to effectively combine MRI and thermotherapy and is thus readily adaptable to existing imaging hardware.