The main objective of this study was to measure and determine the efficiency of poly-crystalline, mono-crystalline and amorphous silicon solar module by applying single-axis time/date solar tracker to the installation of photovoltaic panel (dynamic system) as a strategy to increase the performance of the modules under hot-humid climate of Malaysia. The dynamic system in this experiment was designed to support the three types of PV panels which allowed it to move with single degree of freedom (horizontally) according to the sun’s orientation (sunrise to sunset) from east to west. Studies on sun movement in equator countries have been conducted to locate the sun‘s position on site (azimuth and altitude angle) using the Stereographic Diagram and Tabulate Daily Solar Data. It was found that poly-crystalline solar module have shown better performance ratio and average module efficiency compare to the others tested PV module under Malaysian climate.

No abstract

No abstract

Building sector is associated with high energy consumption and greenhouse gas emissions, which contribute to climate change. Sustainable development emphasizes any actions to reduce climate change and its effect. In Malaysia, half of the energy utilized in buildings goes towards building cooling. Thermal comfort studies and adaptive thermal comfort models reflect the high comfort temperatures for Malaysians in naturally conditioned buildings, which make it possible to tackle the difference between buildings’ indoor temperature and the required comfort temperature by using proper passive measures. This study investigates the effectiveness of building’s retrofitting with phase change materials (PCMs) as a passive cooling technology to improve the indoor thermal environment for more comfortable conditions. PCM sheets were numerically investigated below the internal finishing of the walls. The investigation involved an optimization study for the PCMs transition temperatures and quantities. The results showed significant improvement in the indoor thermal environment, especially when using lower transition temperatures and higher quantities of PCMs. Therefore, the monthly thermal discomfort time has decreased completely, while the thermal comfort time has increased to as high as 98%. The PCM was effective year-round and the optimum performance for the investigated conditions was achieved when using 18mm layer of PCM27-26.

No abstract

No abstract

Fossil fuel consumption for electricity generation in the building sector is at an all-time high in line with the country’s economic growth. This scenario will increase the global CO2 emissions and large carbon footprints, thus leading to global warming. In recent years, most of the research related to the building sector has focused on the development of new techniques to reduce buildings’ energy consumption through energy conservation, energy efficiency, and the implementation of renewable energy technologies. The introduction of photovoltaic (PV) technology has become the most prominent renewable energy (RE) that can be integrated into building components. Even though the Building Integrated Photovoltaic (BIPV) has been available for decades, but its implementation in Southeast Asian countries has not gained widespread acceptance compared to European countries and other parts of Asia. This paper aims to investigate the effects and challenges of BIPV implementation in Southeast Asian Countries (Cambodia, Indonesia, Laos, Malaysia, Singapore, Thailand, Vietnam, and the Philippines), focusing on climate effects, the initial cost of PV technology, government policies, and initiatives. An in-depth literature review from past research, policies, and reports taken between 2016 to 2021 has been conducted and found that the environmental parameters directly influence the performance of BIPV systems and affect efficiency. This study pointed at Feed-in Tariff (FiT), policies and initiatives offered by the government in Southeast Asian countries are not beneficial and discourage building owners to adopt the BIPV technology or any other RE technology. Governments should revise the current policies to promote and attract more building owners to take part in the efforts to minimize CO2 emissions from the building industry.

Daylight performance in a velodrome cycling track arena is essential to create splendid scenery for the athlete to perform during the event held. Therefore, a moveable kinetic roof according to the sunlight path on top of the building is important to implement. A specific requirement for cycling track is to avoid any shadow from the cyclist to steer clear any incident from happening during the game begins. The new technology of kinetic roof that integrate creativity with the sun movement would help to control the amount of sunlight that will enter the indoor area. The integration of kinetic roof to be placed at the top of the sports indoor arena would help to reduce the electricity consumption for that building as it integrates to control the amount of light to pass through into the private area. This study is divided into two parts; the analysis on the preference of local velodrome in Malaysia, which is in Nilai, Negeri Sembilan and 3D model daylight analysis using VELUX. Based on the analysis, the implementation of the kinetic roof in velodrome design in Malaysia will be able to let the required amount of daylight appear for the internal area. While passive skylight that integrated at the current velodrome was not capable of controlling the daylight and it is dependable on the weather condition.