This research work primarily focused on investigating the effects of changing rotational speed on the forming temperature and microstructure during incremental sheet metal forming (ISF) of AA-2219-O and AA-2219-T6 sheets. Tool rotational speed was varied in the defined range (50–3000 rpm). The tool feed rate of 3000 mm/min and step size of 0.3 mm with spiral tool path were kept fixed in the tests. The sheets were formed into pyramid shapes of 45° draw angle, with the hemispherical end forming tool of 12 mm diameter. While the sheets were forming, the temperature variation due to friction at the sheet–tool contact zone was recorded, using a non-contact laser projected infrared temperature sensor. It was observed that the temperature rising rate for the T6 sheet during ISF is higher as compared to the annealed sheet, thereby showing that the T6 tempered sheet offers higher friction than the annealed sheet. Due to this reason, the T6 tempered sheet fails to achieve the defined forming depth of 25 mm when the rotational speed exceeds 2000 rpm. The effects of rotational speed and associated rise in the temperature were examined on the microstructure, using the scanning electron microscopic (SEM). The results reveal that the density of second phase particles reduces with increasing speed reasoning to corresponding temperature rise. However, the particle size in both tempers of AA2219 received a slight change and showed a trivial response to an increase in the rotational speed.

No abstract

Due to continuous worsening of the environment and depletion of natural resources, concept of sustainability in manufacturing sector is gaining an increasing attention. New processes and strategies characterized by efficient use of energy and materials, low processing time and zero or nearly zero green-house emissions are being explored. Incremental sheet forming (ISF) is a comparatively new sheet forming process with high economic payoff for small production runs and customized orders. The current study presents a comprehensive review on the sustainability aspects of the process. The process performance in terms of power demand, energy consumption, cost, CO2 emissions, processing time, and material wastage/usage is analyzed on the basis of published literature, and important conclusions and recommendations are drawn to utilize the process for cleaner, economical and time efficient production. The review establishes that ISF is more sustainable process than conventional forming methods for small production runs. Further, its sustainability performance can be further enhanced by choosing optimum process conditions especially lower spindle rotation, larger feed rate and step size. Shorter tool paths and advent of energy efficient machines is likely to further elevate the process performance. The review also identifies future work and presents fundamental guidelines and recommendations for establishing the sustainable ISF process.

This research investigates the performance of medium density fiberboard (MDF) with respect to hot press parameters. The performance of the board, type of glue, and production efficiency determine the optimum temperature and pressure for hot pressing. The actual temperature of the hot press inside the MDF board determines the properties of the final product. Hence, the optimal hot press parameters for the desired product are experimentally obtained. Moreover, MDF is experimentally investigated in terms of its vertical density profile, bending, and internal bonding under the various input parameters of temperature, pressure, cycle time, and moisture content during the manufacturing process. The experimental study is carried out by varying the temperature, pressure, cycle time, and moisture content in the ranges of 200–220 °C, 145–155 bar, 260–275 s, and 8–10%, respectively. Consequently, the optimum input parameters of a hot-pressing temperature of 220 °C, pressure of 155 bar, cycle time of 256 s, and moisture content of 8% are identified for the required internal bonding (0.64 N/mm2), bending (32 N/mm2), and increase in both the core and peak density of the vertical density profile as per the ASTM standard.

Friction and plastic deformation at the tool–chips interaction during a dry drilling process results in temperature rise and promotes tool wear and surface roughness. In most of the components produced in industries, a drilling process is used to make a hole for final assembly. Therefore, knowledge of temperatures produced during drilling operation at various machining input parameters is required for the best quality product. A fuzzy logic-based algorithm is developed to predict the temperature generated in the drilling process of AISI 1018 mild steel. The algorithm used speed and feed rate of the drill bit as input parameters to the fuzzy domain. A set of rules was used in the fuzzy domain to predict maximum temperature produced in the drilling process. The developed algorithm is simulated for various input speed and feed rate parameters and was verified through the maximum temperature measured during drilling of the studied material at selected speed–feed combinations. Experiments were conducted to validate the results of developed fuzzy logic-based algorithm by using non-contact infrared pyrometer for drilling of AISI 1018 steel. A good agreement between the predicted and experimentally measured maximum temperature was observed with an error less than 6%. It is found that temperature increases with increase in cutting speed and feed rate. Size of roll back burr formation at the hole perimeter significantly increases with increase in drill speed and feed rate. Segmental continuity in spiral or helix chips morphology is more at low feed and high cutting speed. Chip radius increases with increase in feed rate and results in damaging of the machined surface and causes burr formation while the radius decreases with cutting speed along with improved hole surface finish.